manualshive.com logo in svg

Toro Recycler 20377, Operator'S Manual, Page: 17 / 24

Share
Download
Toro Recycler 20377 Operator'S Manual Download Page 17

Servicing the Air Filter

Service Interval:

Before each use or daily—Check

the air filter for dirty, loose, or
damaged parts, and clean or
replace them if necessary.

Every 25 hours/Yearly (whichever comes
first)—Replace the air-filter element (more
frequently when operating the machine in dusty
or dirty operating conditions).

1.

Perform the pre-maintenance procedures; refer
to

Preparing for Maintenance (page 16)

.

2.

Press down on the latch tabs on top of the
air-filter cover (

Figure 22

).

g027312

Figure 22

1.

Latch tabs

2.

Air-filter element

3.

Open the cover.

4.

Replace the air-filter element.

5.

Install the cover.

Changing the Engine Oil

Changing the engine oil is not required, but if
you want to change the oil, use the following
procedure.

Note:

Run the engine a few minutes before changing

the oil to warm it. Warm oil flows better and carries
more contaminants.

Engine Oil Specifications

Engine oil capacity

0.60 L (20 fl oz)

Oil viscosity

SAE 30 or SAE 10W-30
detergent oil

API service classification

SJ or higher

1.

Move the machine to a level surface.

2.

Refer to

Preparing for Maintenance (page 16)

.

3.

Remove the dipstick by rotating the cap
counterclockwise and pulling it out (

Figure 23

).

g188681

Figure 23

4.

Tip the machine onto its side (so that the air
filter is up) to drain the used oil from the oil-fill
tube (

Figure 23

).

17

 

Summary of Contents for Recycler 20377

























Reviews:

No comments