background image

This product complies to the US National Highway Traffic
Safety Administration (NHTSA) for street legal trailer.

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals

known to the State of California to cause cancer,

birth defects, or reproductive harm.

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

Important:

This engine is not equipped with a spark

arrester muffler. It is a violation of California Public
Resource Code Section 4442 to use or operate the engine
on any forest-covered, brush-covered, or grass-covered
land. Other states or federal areas may have similar laws.

Electromagnetic Compatibility

Domestic:

This device complies with FCC rules Part 15.

Operation is subject to the following two conditions: (1) This
device may not cause harmful interference and (2) this device
must accept any interference that may be received, including
interference that may cause undesirable operation.

This equipment generates and uses radio frequency energy and
if not installed and used properly, that is, in strict accordance
with the manufacturer's instructions, may cause interference
to radio and television reception. It has been type tested and
found to comply with the limits for a FCC Class B computing
device in accordance with the specifications in Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:Reorient the receiving antenna, relocate
the remote control receiver with respect to the radio/TV antenna
or plug the controller into a different outlet so that the controller
and radio/TV are on different branch circuits.If necessary, the
user should consult the dealer or an experienced radio/television
technician for additional suggestions.The user may find the
following booklet prepared by the Federal Communications
Commission helpful: "How to Identify and Resolve Radio-TV
Interference Problems". This booklet is available from the U.S.
Government Printing Office, Washington, DC 20402. Stock No.
004-000-00345-4.

FCC ID: LOBSBU200-Base, LOBSHH200-Hand Held

IC: 7955A-SBU200-Base, 7955A-SHH200-Hand Held

Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.

CAUTION

If a user makes changes or modifications not
expressly approved by the party responsible for
compliance, they could void the user's authority to
operate the equipment.

This spark ignition system complies with Canadian ICES-002.

Introduction

The debris blower is towed behind a ride-on machine which
is intended to be used by professional, hired operators in
commercial applications. It is primarily designed to use wind
power to quickly clear large areas of unwanted debris on
well-maintained lawns in parks, golf courses, sports fields,
and on commercial grounds.

Read this information carefully to learn how to operate and
maintain your product properly and to avoid injury and
product damage. You are responsible for operating the
product properly and safely.

You may contact Toro directly at www.Toro.com for product
and accessory information, help finding a dealer, or to register
your product.

Whenever you need service, genuine Toro parts, or additional
information, contact an Authorized Service Dealer or Toro
Customer Service and have the model and serial numbers of
your product ready. Figure 1 identifies the location of the
model and serial numbers on the product. Write the numbers
in the space provided.

1

G020710

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has safety
messages identified by the safety alert symbol (Figure 2),

© 2013—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

2

Contact us at www.Toro.com.

Printed in the USA.

All Rights Reserved

Summary of Contents for ProForce 44539

































Reviews: