background image

Charging the Battery Pack

Important:

Read all safety precautions.

Important:

For best results, charge your battery pack

in a location where the temperature is more than 0°C
(32°F) but less than 50°C (122°F). To reduce the risk
of serious personal injury, do not store it outside or in
vehicles. Charging time increases if you do not charge
it within this range.

Note:

At any time, press the battery-charge-indicator button

on the battery pack to display the current charge (LED
indicators).

1.

Make sure that the vents on the battery pack are clear
of any dust and debris.

2.

Line up the cavity in the battery pack (

Figure 10

) with

the tongue on the charger.

g192748

Figure 10

1.

Battery pack cavity

4.

Battery-charge-indicator
button

2.

Battery pack terminals

5.

LED indicators (current
charge)

3.

Battery pack venting areas

3.

Make sure that the vents on the battery charger are
clear of any dust and debris.

4.

Slide the battery pack into the charger until it is fully
seated (

Figure 11

).

g194423

Figure 11

1.

Charger venting areas

3.

Right indicator light

2.

Left indicator light

5.

To remove the battery pack, slide the battery backward
out of the charger.

6.

Refer to the following table to interpret the LED
indicators on the battery charger.

10

 

Summary of Contents for Power Plex 51481

















Reviews: