background image

Form No. 3355-498 Rev B

Power Max® 828LXE Snowthrower

Model No. 38631—Serial No. 270000001 and Up

Operator's Manual

Introduction

Read this information carefully to learn how to operate and
maintain your product properly and to avoid injury and
product damage. You are responsible for operating the
product properly and safely.

You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a dealer,
or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model and
serial numbers of your product ready. Figure 1 identifies the
location of the model and serial numbers on the product.
Write the numbers in the space provided.

Figure 1

1. Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has safety
messages identified by the safety alert symbol (Figure 2),
which signals a hazard that may cause serious injury or
death if you do not follow the recommended precautions.

Figure 2

1. Safety alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical information

and

Note

emphasizes general information worthy of special

attention.

Replacement Engine Owner’s Manuals may be ordered
through the engine manufacturer.

© 2006—The Toro® Company

8111 Lyndale Avenue South

Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

Summary of Contents for Power Max 828LXE





























Reviews: