manualshive.com logo in svg

Toro Polar Trac Cab 30474, Operator'S Manual

Share
Download
Toro Polar Trac Cab 30474 Operator'S Manual Download Page 24

3.

At the fuse block (

Figure 41

), connect the

following wire pairs:

Component

Wire color

Connector type

Kit wire
harness—auxiliary
power wire

Green

Insulated blade
connector

Fuse
block—machine
wire harness
(options relay)

Pink

Insulated socket
connector

Note:

If the auxiliary-power wire is used in another
circuit, install an additional wire harness fuse
block and key start harness; refer to steps

1

through

3

.

4.

Install the fuse (10 A) into the fuse-block slot
(

Figure 41

).

5.

Use the cable ties to secure the wire.

Note:

Do not secure the wire harness to hot or

moving parts.

Connecting the Auxiliary-Power
Wire—Additional Wire Harness
Fuse Block

Note:

Use this procedure if you do not have an open

slot in the fuse block for the machine.

1.

Assemble the additional wire harness fuse block
(Part No. 92-2641) onto the fuse block of the
machine (

Figure 42

).

g234232

Figure 42

1.

Wire harness fuse block
(Part No. 92-2641)

5.

Blue wire—18 gauge (key
start harness—Part No.
107-0672)

2.

Fuse (10 A)

6.

Red wire—12 gauge (wire
harness fuse block—Part
No. 92-2641)

3.

Fuse block of the machine

7.

Red wire—10 gauge (wire
harness fuse block—Part
No. 92-2641)

4.

Green wire—18 gauge
(Polar Trac kit harness)

8.

Pink wire (fuse block of
the machine)

2.

Connect the wire harness fuse block (Part No.
92–2641) to the fuse block (

Figure 42

) of the

machine as follows:

Component

Wire color

Connector type

Wire harness fuse
block (Part No.
92-2641)

Red (10 gauge)

Blade connector

Fuse
block—machine
wire harness

Red (10
gauge—optional
fuse block)

Socket connector

3.

Connect the key start harness (Part No.
107-0672) to the harness fuse block (Part No.
92–2641) wire (

Figure 42

) as follows:

Component

Wire color

Connector type

Key start harness
(Part No.
107-0672)

Blue (18 gauge)

Uninsulated socket
connector

Wire harness fuse
block (Part No.
92-2641)

Red (12 gauge)

Insulated blade
connector

4.

Connect the key start harness (Part No.
107-0672) to the auxiliary-power wire of the
Polar Trac kit harness (

Figure 42

) as follows:

24

 

Summary of Contents for Polar Trac Cab 30474





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands