background image

Form No. 3413-860 Rev A

EU Light Kit

Serial Number 400000000 and After Groundsmaster

®

5900 or 5910

Series Rotary Mower with Cab

Model No. 30653—Serial No. 400000000 and Up

Installation Instructions

This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at
the back of this publication.

Safety

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
Replace any decal that is damaged or missing.

decal136-0007

136-0007

1.

Brakes

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure

Description

Qty.

Use

1

No parts required

Prepare the machine.

2

No parts required

Disconnect the battery.

Flasher module

1

Wire harness

1

Switch

1

3

Auxiliary-brake decal

1

Install the flasher module.

Right headlight mount

1

Left headlight mount

1

Cover panel

2

Plug

8

Right headlight assembly

1

4

Left headlight assembly

1

Install the headlights (for machines with
ROPS only).

© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3413-860* A

 

Summary of Contents for Groundsmaster 5900 Series

















Reviews: