manualshive.com logo in svg

Toro Greensmaster 1018, Service Manual

Share
Download
Toro Greensmaster 1018 Service Manual Download Page 61

Reel Drive Assembly

g258675

Figure 22

1.

Screw (2 each)

5.

V-ring seal

9.

RH side plate

2.

Spacer (2 each)

6.

Reel drive assembly

10.

Transmission drive shaft

3.

Washer (2 each)

7.

Compression spring

11.

Spacer

4.

Spring washer (2 each)

8.

Telescopic coupler

12.

Nut

Removing the Reel Drive Assembly

Note:

Refer to

Figure 22

during this procedure.

1. Park the machine on a level surface. Ensure that the engine is OFF. Remove

the spark plug wire from the engine spark plug.

2. Slide the telescopic coupler (item 8 in

Figure 22

) on the reel drive assembly

(6) and disconnect the reel drive shaft from the transmission drive shaft (10).

3. Loosen and remove the 2 screws (1) and the nut (12) that secures the reel

drive assembly (6) to RH side plate (9). Remove the reel drive assembly
(6), flat washers (3), spring washers (4) and spacers (2 and 11) from the
RH side plate (9).

4. Remove the V-ring seal (5) from the reel drive assembly (6).

Greensmaster

®

1018/1021/1026

Page 5–7

Traction and Reel Drive Systems: Service and Repairs

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands