Toro Grandstand 78524 Operator'S Manual Download Page 19

Maintenance

CAUTION

If you leave the key in the switch, someone could accidently start the engine and seriously
injure you or other bystanders.

Remove the key from the switch before you perform any maintenance.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 8 hours

• Inspect the bagger belt.
• Inspect the bagger.

After each use

• Clean the bagger, bags, and fill-indicator impeller.

Every 25 hours

• Inspect the bagger belt.
• Inspect the impeller assembly.

Every 100 hours

• Inspect the bagger.

Cleaning the Bagger and
Bags

Service Interval:

After each use

Note:

If you do not clean the bagger, dried grass can

accumulate and clog the blower housing and tube.

1.

Wash the inside and outside of the bagger
hood, bags, tube, fill-indicator impeller, and
the underside of the machine. Use a mild
automotive detergent to remove dirt.

2.

Make sure that you remove matted grass from
all parts.

3.

After washing all parts, let them dry thoroughly.

Note:

With all parts installed, start and run the

machine for a minute to assist in drying.

Inspecting the Bagger Belt

Service Interval:

After the first 8 hours

Every 25 hours

Check belts for cracks, frayed edges, burn marks, or
any other damage. Replace damaged belts.

Replacing the Bagger Belt

1.

Disengage the PTO, move the motion-control
levers to the N

EUTRAL

-

LOCK

position, and

engage the parking brake.

2.

Shut off the engine, remove the key, and wait
for all moving parts to stop before leaving the
operating position.

3.

Lower the mower deck to the lowest setting.

4.

Loosen the knob on the belt cover and remove
the cover.

5.

Open the blower assembly to access the belt
and pulley.

6.

Pull back on the spring-loaded idler pulley to
relieve the belt tension (

Figure 26

).

g256119

Figure 26

1.

Belt

2.

Spring-loaded idler pulley

7.

Remove the existing bagger belt from the deck
and blower assembly by rotating the blower
pulley as you pull the belt off.

8.

Install the belt around the blower and idler
pulleys as shown in

Figure 27

. Place the belt

19

 

Summary of Contents for Grandstand 78524

























Reviews: