background image

Rev. 6/4/98

6

Subject to the warranty condition below, this tool
(hereinafter called “the product”) is warranted by Toro
Australia (hereinafter called “the Company”) to be
free from defects in material or workmanship for a
period of 24 months from the date of original
purchase covering both parts and labour. Under the
terms of this warranty, the repair or replacement of
any part shall be the opinion of the Company or its
authorised agent. Should service become necessary
during the warranty period, the owner should contact
the Authorised Toro Retailer from whom the product
was purchased, or the nearest Company Branch
Office. In order to obtain warranty service, the owner
must present the sales docket and Warranty
Certificate to confirm date of purchase. This product
is sold by the dealer or agent as principal, and the
dealer has no authority from the Company to give
any additional warranty or guarantee on the
Company’s behalf except as herein contained or
herein referred to.

Warranty Conditions

This warranty applies provided the product has been
used in accordance with the manufacturer’s
recommendations under normal use and reasonable

TORO AUSTRALIA POWER EQUIPMENT WARRANTY

care (in the opinion of the Company), and such
warranty does not cover damage, malfunction or
failure resulting from misuse, neglect, abuse or use
for a purpose for which it was not designed or is not
suited; and no repairs, alterations or modifications
have been attempted by other than an
Authorised Service Agent. This guarantee will not
apply if the tool is damaged by accident or if repairs
arise from normal wear and tear.

The Company accepts no additional liability
pursuant to this warranty for the costs of travelling
or transportation of the product to and from the
service dealer or agent – which costs are not
included in this warranty.

Certain legislation, including the Trade Practices
Act, 1974 (as amended) and other state and
territorial laws give rights to the buyer and impose
liability on the seller in certain circumstances.
Nothing herein shall have the effect of excluding,
restricting or modifying any condition, warranty,
right or liability imposed, to the extent only that such
exclusion, restriction or modification would render
any term herein void.

Toro Australia Pty Limited

A.C.N. 001 310 443 Incorporated in S.A.

Adelaide: 53 Howards Road, Beverley, SA 5009
131 588

Brisbane: Unit 2, 480 Nudgee Road, Hendra
QLD 4011 (07) 3268 1385

Perth: Unit 3, 21 Ledgar Road, Balcatta WA 6021
(08) 9478 3773

Sydney: Unit 4, 148-308 James Ruse Drive
Parramatta NSW 2150 (02) 9687 2366

Melbourne: 59 Woodlands Drive, Braeside,
VIC 3195 (03) 9580 7355

For your record and to assist in establishing date of purchase (necessary for in-warranty service), please
keep your purchase docket and this form completed with the following particulars:

This Warranty Form should be retained by the customer at all times

Purchasing from:

Address of Dealer:

Date:

Model No.

Serial No.

Present this form with your purchase docket when warranty service is required.

Summary of Contents for Air Rake 51551













Reviews: