Toro Air Cool Z Master 96in 74090 Software Manual Download Page 4

Screen

The screen displays icons and information relative to
machine operation and is backlit for viewing in low light
situations. The screen is located above the buttons.

Refer to the

Screen Icons (page 1)

section for icon

descriptions.

LED Status Light

The LED status light is multi-colored to indicate the
system status and is located on the right side of the
panel. During startup, the LED illuminates red to
orange to green to verify functionality.

Solid Green:

indicates normal operating activity

Blinking Red:

indicates that a fault is active

Blinking Green and Orange:

indicates that a

clutch reset is required

Buttons

The multi-functional buttons are located at the bottom
of the panel. The icons displayed on the information
screen above the buttons indicate the current function.
The buttons allow you to select the engine speed and
navigate through system menus.

Alarm

If an error occurs, an error message displays, the LED
turns red, and the alarm sounds audibly as follows:

A fast chirp sound indicates critical errors.

A slow chirping sound indicates less critical errors,
such as required maintenance or service intervals.

Note:

During startup, the alarm sounds briefly to

verify functionality.

Information Screens

The main information screens are as follows:

Startup Screen (page 4)

Engine-Off Screen (page 4)

Engine-On Screen (page 4)

Startup Screen

During startup, the screen displays a startup graphic
for 1 second, sounds the alarm, and illuminates the
LED, changing from red to orange to green.

Engine Screens

Engine-Off Screen

When the key is on without the engine running, the
Engine-Off screen displays (

Figure 3

).

g030172

Figure 3

1.

Hours remaining until transmission oil maintenance is
required

2.

Battery voltage display

3.

Safety interlock status indicators

4.

Fuel-level gauge (if fuel sender is available)

5.

Screen toggles between hours remaining until engine oil
maintenance and non-resettable engine hour counter

Engine-On Screen

When the engine is running, the Engine-On screen
displays (

Figure 4

).

g257021

Figure 4

1.

Engine speed mode

4.

Engine speed

2.

Safety interlock status
indicators

5.

Fuel level gauge (if fuel
sender is available)

3.

Engine temperature

4

 

Summary of Contents for Air Cool Z Master 96in 74090

















Reviews: