background image

Form No. 3417-740 Rev A

Horizon Control Module

For Z Master Lawn Mowers

Model No. 74946—Serial No. 402000000 and Up

Model No. 74947—Serial No. 40200000 and Up

Model No. 74969—Serial No. 400000000 and Up

Software Guide

Read this information carefully to learn how to operate and maintain your product properly and to avoid injury
and product damage. You are responsible for operating the product properly and safely. Read your

Operator’s

Manual

for more information.

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California

to cause cancer, birth defects, or reproductive harm.

Screen Icons

The information screen uses the following icons:

Gauge and Meters

Low Engine Speed

Processing

Advanced Settings

Transmission Oil Maintenance

Battery Voltage

Maintenance and Service

Engine-Oil Temperature

Engine Hours

Fuel Level

Engine Oil Maintenance

Cancel/Exit

© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3417-740* A

 

Summary of Contents for 74946

















Reviews: