manualshive.com logo in svg

Toro 74560, Operator'S Manual

Share
Download
Toro 74560 Operator'S Manual Download Page 8

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or lost.

93-7276

1.

Explosion hazard—wear eye protection.

2.

Caustic liquid/chemical burn hazard—to perform first aid,
flush with water.

3.

Fire hazard—no fire, open flames, or smoking.

4.

Poison hazard—keep children a safe distance from the
battery.

99-5340

1.

KeyChoice—turn to enable reverse mowing.

119-2725

1.

Warning—read the

Operator's Manual

.

2.

Warning—remove the spark plug wire before performing
any maintenance on the machine.

3.

Tipping hazard—do not operate on slopes greater than 10
degrees.

4.

Thrown object hazard; crushing hazard, bystanders—keep
bystanders a safe distance from the machine.

5.

Cutting hazard of hand or foot—stay away moving parts,
keep all guards and shields in place.

119-2726

1.

Thrown object hazard—keep bystanders a safe distance
from the machine.

2.

Cutting hazard of hand or foot—stay away moving parts,
keep all guards and shields in place.

8

Summary of Contents for 74560









































Reviews:

No comments

Brands by name

Popular brands

Load more brands