manualshive.com logo in svg

Toro 74408 Z334 Z Master, Operator'S Manual

Share
Download
Toro 74408 Z334 Z Master Operator'S Manual Download Page 3

Controls ............................................................. 10

Operation................................................................... 11

Adding Fuel ....................................................... 11
Checking the Engine Oil Level............................ 12
Think Safety First ............................................... 12
Operating the Parking Brake ............................... 13
Starting and Stopping the Engine ........................ 14
Operating the Power Take Off (PTO) ................. 15
The Safety Interlock System................................ 15
Driving Forward or Backward............................. 16
Stopping the Machine......................................... 17
Adjusting the Height-of-Cut ............................... 17
Using the Lift Assist Pedal .................................. 17
Adjusting the Anti-Scalp Rollers ......................... 18
Positioning the Seat ............................................ 18
Pushing the Machine by Hand............................. 18
Using the Side Discharge .................................... 19
Transporting Machines ....................................... 19
Loading Machines .............................................. 20
Operating Tips ................................................... 20

Maintenance............................................................... 22

Recommended Maintenance Schedule(s) ................ 22
Lubrication............................................................. 22

Greasing and Lubrication ................................... 22
Lubricating the Caster Wheel Hubs ..................... 24

Engine Maintenance............................................... 26

Servicing the Air Cleaner .................................... 26
Servicing the Engine Oil ..................................... 27
Servicing the Spark Plugs.................................... 28

Fuel System Maintenance ....................................... 29

Draining the Fuel Tank ....................................... 29
Replacing the Fuel Filter ..................................... 29

Electrical System Maintenance................................ 30

Servicing the Battery........................................... 30
Servicing the Fuses ............................................. 32

Drive System Maintenance ..................................... 33

Checking the Tire Pressure ................................. 33
Adjusting the Caster Pivot Bearing ...................... 33

Cooling System Maintenance .................................. 34

Cleaning the Air Intake Screen ............................ 34
Cleaning the Engine Cooling System ................... 34

Brake Maintenance ................................................. 34

Servicing the Brakes ........................................... 34

Belt Maintenance.................................................... 35

Inspecting the Belts ............................................ 35
Replacing the Mower Belt ................................... 35
Checking and Replacing the Pump Drive

Belt ................................................................ 35

Controls System Maintenance................................. 36

Adjusting the Control Handle Neutral

Position.......................................................... 36

Adjusting the Tracking........................................ 37

Hydraulic System Maintenance ............................... 38

Servicing the Hydraulic System ........................... 38

Mower Deck Maintenance ...................................... 40

Leveling the Mower ............................................ 40
Servicing the Cutting Blades ............................... 41
Replacing the Grass Deflector............................. 44

Cleaning ................................................................. 45

Cleaning Under the Mower ................................. 45
Waste Disposal ................................................... 45

Storage ....................................................................... 45
Troubleshooting......................................................... 47
Schematics ................................................................. 49

3

Summary of Contents for 74408 Z334 Z Master





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands