Toro 74259 Operator'S Manual Download Page 60

LCE

The Toro Total Coverage Guarantee

A Limited Warranty

Conditions and Products Covered

The Toro Company and its affiliate, Toro Warranty Company,
pursuant to an agreement between them, jointly promise to repair
the listed Toro Products if defective in materials or workmanship.
The following time periods apply from the date of purchase:

Products

Warranty Period

All Products

1 year

All Spindles

2 years parts and labor;

third year, parts only

Engines/Hydraulic Systems* on
the following:

2 years

Outfront and Mid-Mount Z’s
ProLine Mid-Size Mowers
Groundsmaster

 Riding Mowers

Backpack Blowers

Deck Shells (36

–72

) on the

following:

2 years

ProLine Mid-Size Mowers
Mid-Mount Z’s

Electric Clutch on 200 Series
Mid-Mount Z’s

2 years

This warranty includes the cost of parts and labor, but you must
pay transportation costs.

This warranty applies to:

Outfront and Mid-Mount Z’s

ProLine Mid-Size Mowers

Groundsmaster Riding Mowers

Turf Maintenance Equipment

Debris Management Equipment

* Some engines used on Toro LCE Products are warranted by the

engine manufacturer.

Instructions for Obtaining Warranty Service

If you think that your Toro Product contains a defect in materials or
workmanship, follow this procedure:

1Contact any Toro Authorized or Master Service Dealer to

arrange service at their dealership. To locate a dealer
convenient to you, access our website at www.Toro.com. U.S.
Customers may also call 800-348-2424.

2Bring the product and your proof of purchase (sales receipt) to

the Service Dealer.

If for any reason you are dissatisfied with the Service Dealer’s
analysis or with the assistance provided, contact us at:

LCB Customer Service Department
Toro Warranty Company
8111 Lyndale Avenue South
Bloomington, MN  55420-1196
888-577-7466 (U.S. customers)
877-484-9255 (Canada customers)

Owner Responsibilities

You must maintain your Toro Product by following the maintenance
procedures described in the operator’s manual. Such routine
maintenance, whether performed by a dealer or by you, is at your
expense.

Items and Conditions Not Covered

There is no other express warranty except for special emission
system coverage on some products. This express warranty does
not cover the following:

Cost of regular maintenance service or parts, such as filters,
fuel, lubricants, tune-up parts, blade sharpening, brake and
clutch adjustments.

Any product or part which has been altered or misused or
required replacement or repair due to normal wear, accidents,
or lack of proper maintenance.

Repairs necessary due to improper fuel, contaminants in the
fuel system, or failure to properly prepare the fuel system prior
to any period of non-use over three months.

Pickup and delivery charges.

All repairs covered by this warranty must be performed by an
Authorized Toro Service Dealer using Toro approved replacement
parts.

General Conditions

Repair by an Authorized Toro Service Dealer is your sole remedy
under this warranty.

Neither The Toro Company nor Toro Warranty Company is liable
for indirect, incidental or consequential damages in connection
with the use of the Toro Products covered by this warranty,
including any cost or expense of providing substitute equipment or
service during reasonable periods of malfunction or non-use
pending completion of repairs under this warranty.

Some states do not allow exclusions of incidental or consequential
damages, or limitations on how long an implied warranty lasts, so
the above exclusions and limitations may not apply to you.

All implied warranties of merchantability (that the product is fit for
ordinary use) and fitness for use (that the product is fit for a
particular purpose) are limited to the duration of the express
warranty.

This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.

Countries Other than the United States or Canada

Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer)
to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or
have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty
Company.

Part No. 374-0037 Rev. C

Summary of Contents for 74259





























































Reviews: