manualshive.com logo in svg

Toro 68021HD, Operator'S Manual

Share
Download
Toro 68021HD Operator'S Manual Download Page 30

10.

Dip the foam element in clean engine oil, then squeeze
out the excess oil.

Note:

Excess oil in the foam element restricts the air

flow through the element and may reach the paper
filter and clog it.

11.

Wipe dirt from the base and the cover with a moist rag.

Note:

Be careful to prevent dirt and debris from

entering the air duct leading to the carburetor.

12.

Install the air-cleaner elements and ensure that they are
properly positioned.

13.

Securely install the cover with the nut.

Servicing the Engine Oil

Toro Premium Engine Oil is available from your Authorized
Toro Dealer.

Important:

Use 4-cycle engine oil that meets or exceeds

the requirements for API service category

SJ, SL, SM,

or higher.

Crankcase Capacity:

1.1 L (1.2 US qt)

Important:

If the oil level in the crankcase is too low

or too high and you run the engine, you may damage
the engine. This type of damage is not covered by the
warranty.

Note:

Use SAE 10W-30 for general use. You can use

the other viscosities shown in the chart when the average
temperature in your area is within the indicated range (

Figure

40

).

g013375

0      20     40      60     80    100   F

-20   -10   0     10     20    30    40  C

o

o

30

5W - 30 / 10W - 30

Figure 40

Checking the Engine-Oil Level

Service Interval:

Before each use or daily

1.

Place the machine on a flat, level surface, and shut off
the engine.

2.

Allow the engine to cool.

3.

Clean around the dipstick.

4.

Check the oil level as shown in

Figure 41

.

Figure 41

30

 

Summary of Contents for 68021HD













































Reviews:

No comments

Brands by name

Popular brands

Load more brands