background image

This product complies with all relevant European directives,
for details please see the separate product specific Declaration
of Conformity (DOC) sheet.

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals

known to the State of California to cause cancer,

birth defects, or reproductive harm.

Introduction

The debris blower is mounted to a ride-on machine which
is intended to be used by professional, hired operators in
commercial applications. It is primarily designed to use wind
power to quickly clear large areas of unwanted debris on
well-maintained lawns in parks, golf courses, sports fields,
and on commercial grounds.

Read this information carefully to learn how to operate and
maintain your product properly and to avoid injury and
product damage. You are responsible for operating the
product properly and safely.

You may contact Toro directly at www.Toro.com for product
and accessory information, help finding a dealer, or to register
your product.

Whenever you need service, genuine Toro parts, or additional
information, contact an Authorized Service Dealer or Toro
Customer Service and have the model and serial numbers of
your product ready. Figure 1 identifies the location of the
model and serial numbers on the product. Write the numbers
in the space provided.

1

G021671

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has safety
messages identified by the safety alert symbol (Figure 2),
which signals a hazard that may cause serious injury or death
if you do not follow the recommended precautions.

Figure 2

1.

Safety alert symbol

This manual uses 2 other words to highlight information.

Important

calls attention to special mechanical information

and

Note

emphasizes general information worthy of special

attention.

CAUTION

If a user makes changes or modifications not
expressly approved by the party responsible for
compliance, they could void the user's authority to
operate the equipment.

© 2013—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

2

Contact us at www.Toro.com.

Printed in the USA.

All Rights Reserved

Summary of Contents for 44547





















Reviews: