or turn. The heavier the load, the longer it takes
to stop.
•
Turf and pavement are much more slippery when
they are wet. It can take 2 to 4 times as long to
stop on wet surfaces as on dry surfaces. If you
drive through standing water deep enough to
get the brakes wet, they will not work well until
they are dry. After driving through water, you
should test the brakes to make sure that they work
properly. If they do not, drive slowly while putting
light pressure on the brake pedal. This will dry the
brakes out.
ROPS Safety
Note:
For each machine covered in this
Operator’s
Manual
, a cab installed by Toro is a ROPS.
•
Do not remove the ROPS from the machine.
•
Fasten the seat belt and ensure that you can
release it quickly in an emergency. Always wear
your seat belt when the roll bar is up or on a
machine with a cab installed by Toro.
•
Check carefully for overhead obstructions and do
not contact them.
•
Keep the ROPS in safe operating condition by
thoroughly inspecting it periodically for damage
and keeping all the mounting fasteners tight.
•
Replace any damaged ROPS component. Do not
repair or alter it.
Operating on Hills and Rough
Terrain
Operating the machine on a hill may cause tipping or
rolling of the machine, or the engine may stall and you
could lose headway on the hill. This could result in
personal injury.
•
Do not accelerate quickly or suddenly apply the
brakes when backing down a hill, especially with a
load.
•
Never drive across a steep hill; always drive
straight up or down or go around the hill.
•
If the engine stalls or you begin to lose headway
while climbing a hill, gradually apply the brakes
and slowly back straight down the hill.
•
Turning while traveling up or down hills can be
dangerous. If you have to turn while on a hill, do it
slowly and cautiously. Never make sharp or fast
turns.
•
Heavy loads affect stability. Reduce the weight of
the load and your speed when operating on hills.
•
Avoid stopping on hills, especially with a load.
Stopping while going down a hill takes longer than
stopping on level ground. If you must stop the
machine, avoid sudden speed changes, which
may initiate tipping or rolling of the machine.
Do not suddenly apply the brakes when rolling
backward, as this may cause the machine to
overturn.
•
Reduce speed and load when operating on rough
terrain, uneven ground, and near curbs, holes, and
other sudden changes in terrain. Loads may shift,
causing the machine to become unstable.
WARNING
Sudden changes in terrain may cause
abrupt steering wheel movement, possibly
resulting in hand and arm injuries.
Grip the steering wheel loosely around the
perimeter. Keep your hands clear of the
steering wheel spokes.
Loading
The weight of the cargo can change the center of
gravity of the machine and the handling of it. To
avoid loss of control and personal injury, follow these
guidelines:
•
Liquid loads can shift. This shifting happens
most often while turning, going up or down hills,
suddenly changing speeds, or while driving over
rough surfaces. Shifting loads can cause the
machine to tip over.
•
When operating with a heavy load, reduce your
speed and allow for sufficient braking distance. Do
not suddenly apply the brakes. Use extra caution
on slopes.
•
Be aware that heavy loads increase your stopping
distance and reduce your ability to turn quickly
without tipping over.
Maintenance
•
Only permit qualified and authorized personnel to
maintain, repair, adjust, or inspect the machine.
•
Before performing any maintenance, ensure
that the system has been thoroughly rinsed and
cleaned.
•
Before servicing or making adjustments to the
machine, shutoff the engine, engage the parking
brake, and remove the key to prevent someone
from accidentally starting the engine.
•
To make sure that the entire machine is in good
condition, keep all nuts, bolts, and screws properly
tightened.
•
To reduce the potential for fire, keep the engine
area free of excessive grease, grass, leaves, and
accumulation of dirt.
•
Never use an open flame to check the level or
leakage of fuel or battery electrolyte.
7
Summary of Contents for 41393
Page 88: ...Schematics g034336 Sprayer System Schematic Rev DWG 131 9559 Rev A 88...
Page 89: ...Notes...
Page 90: ...Notes...