Toro 38409 Operator'S Manual Download Page 28

Rev. 7/2/97

What Is Covered By This Express Warranty?

The Toro Company promises to repair any TORO Product

used for normal residential purposes* if defective in materials

or workmanship for a period of two years from the date of

purchase. For single stage snowthrowers, the cost of parts

and labor is included, but the customer pays the transportaĆ

tion costs.
Transportation within a 15 mile radius of the servicing dealer

is covered under this warranty for twoĆstage snowthrowers.

What Products Are Covered By This Warranty?

This warranty applies to all gasoline powered snow products.

How About Commercial Use?

TORO Consumer Products used for commercial, institutional

or rental use are covered by a limited warranty for 45 days

from the date of purchase.

How Do You Get Warranty Service?

Should you feel your TORO Product contains a defect in maĆ

terial or workmanship, contact the dealer who sold you the

product or any Authorized TORO Service Dealer or TORO

Master Service Dealer. The Yellow Pages of your telephone

directory is a good reference source. The dealer will either

arrange service at his/her dealership or recommend another

Authorized Service Dealer who may be more convenient. You

may need proof of purchase (copy of registration card, sales

receipt, etc.) for warranty validation.
If for any reason you are dissatisfied with the Service Dealer's

analysis of the defect in materials or workmanship or if you

need a referral to a TORO Service Dealer, please feel free to

contact us at the following address:

Toro Customer Service Department

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

612-888-8801

800-348-2424

What Must You Do To Keep The Warranty

In Effect?

You must maintain your TORO Product by following the mainĆ

tenance procedures described in the operator's manual.

Such routine maintenance, whether performed by a dealer or

by you, is at your expense.

THE TORO TOTAL COVERAGE

GUARANTEE

A Full TwoĆYear Warranty

(Limited Warranty for Commercial Use)

Gas Powered

Snow

Products

What Does This Warranty Not Cover?

and

How Does Your State Law Relate To This Warranty?

There is no other express warranty except for special emission

system coverage on some products and the TORO Starting

Guarantee on GTS Engines. This express warranty does not

cover:

Cost of regular maintenance service or parts, such as filters,

fuel, lubricants, tuneĆup parts, blade sharpening, brake and

clutch adjustments.

Any product or part which has been altered or misused or

required replacement or repair due to normal wear, accidents,

or lack of proper maintenance.

Repairs necessary due to improper fuel, contaminants in the

fuel system, or failure to properly prepare the fuel system prior

to any period of nonĆuse over three months.

Pickup and delivery charges for distances beyond a 15 mile

radius from an Authorized TORO Service Dealer (covered

products only).
All repairs covered by this warranty must be performed by an

Authorized TORO Service Dealer using Toro approved replaceĆ

ment parts.
Repair by an Authorized TORO Service Dealer is your sole

remedy under this warranty.

The Toro Company is not liable for indirect, incidental or

consequential damages in connection with the use of the

TORO Products covered by this warranty, including any

cost or expense of providing substitute equipment or serĆ

vice during reasonable periods of malfunction or non-use

pending completion of repairs under this warranty. Some

states do not allow exclusions of incidental or consequenĆ

tial damages, so the above exclusion may not apply to

you.
This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

* Normal residential purposes means removing snow on the

same lot as your home. Use at more than one location is

considered commercial use and the commercial use warĆ

ranty would apply.

Customers who have purchased TORO Products exported from the United States or Canada should contact their TORO

Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with

your Distributor's service or have difficulty obtaining guarantee information, contact the TORO importer. If all other remedies

fail, you may contact us at The Toro Company.

COUNTRIES OTHER THAN THE UNITED STATES OR CANADA

Summary of Contents for 38409





























Reviews: