manualshive.com logo in svg

Toro 23511, Operator'S Manual

Share
Download
Toro 23511 Operator'S Manual Download Page 10

Throttle Lever

Move the control forward to increase the engine speed
and rearward to decrease speed; refer to

Figure 6

.

g241996

Figure 6

1.

Throttle lever

Operator-Presence Bail

The operator-presence bail allows the machine to
start and run.

•

To start the machine, hold down the
operator-presence bail (

Figure 7

). Continue to

hold down the operator-presence bail to allow the
machine to run.

g241994

Figure 7

1.

Operator-presence bail

•

To stop the cutting blades, release the
operator-presence bail.

Depth-Control Lever

The depth-control lever allows you to set the depth of
the cutting blades in 10 cutting positions along with
1 position for transportation. To adjust the depth,
remove the hairpin cotter, pull the locking pin out, and
move the lever forward or rearward to the desired
depth setting (

Figure 8

).

Important:

Do not pull the lever side to side as

this will bend it.

g019441

Figure 8

1.

Depth-control lever

3.

Hairpin cotter

2.

Transport-position hole

4.

Locking pin

10

 

Summary of Contents for 23511

























Reviews:

No comments

Brands by name

Popular brands

Load more brands