background image

The Toro Warranty

A limited warranty (see warranty periods below)

Concrete,
Masonry, and
Compaction
Equipment

Conditions and Products Covered

The Toro Company and its affiliate, Toro Warranty Company, pursuant to
an agreement between them, jointly warrant your Toro Concrete, Masonry,
and Compaction Equipment Products listed below to be free from defects in
materials or workmanship.

This warranty covers the cost of parts and labor, but you must pay
transportation costs.

The following time periods apply from the date of purchase:

Products

Warranty Period

Concrete Mixers

1 year

Spindle Bearings

Lifetime* (original owner only)

Mortar Mixers

1 year

Drum Bearings and Seals

Lifetime* (original owner only)

Forward Plate Compactors

2 years

Reversible Plates

1 year

Rammer Compactors

2 years

Mud Buggy

1 year

Vibrating Trench Roller

2 years

Concrete Saws

1 year

Masonry Saws

1 year

Power Trowels

1 year

Screeds

1 year

Concrete Vibrators

1 year

Where a warrantable condition exists, we will repair the Product at no cost
to you including diagnosis, labor, and parts.

*

Lifetime Warranty - If the bearing(s) or seal(s) on your mixer fail, it will be replaced under warranty,

at no cost for parts or labor.

Instructions for Obtaining Warranty Service

If you think that your Toro Product contains a defect in materials or
workmanship, follow this procedure

**

:

1.

Contact any Authorized Servicing Outlet to arrange service at their
dealership. To locate one convenient to you, access our website at
www.Toro.com. Select “Where to Buy” and select “Contractor” under
product type. You may also call our toll free number below.

2.

Bring the product and your proof of purchase (sales receipt) to them.

3.

If for any reason you are dissatisfied with the Service Outlet’s analysis
or with the assistance provided, contact us at:

SWS Customer Care Department
Toro Warranty Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Toll Free: 800-888-9926

**

Toro Authorized Rental Customers who have purchased products directly from Toro and have

signed the Toro Rental Customer Agreement have the ability to perform their own warranty work.

Please visit Toro’s Rental Portal for electronic warranty clam filing procedures or call the toll free

number above.

Owner Responsibilities

You must maintain your Toro Product by following the maintenance
procedures described in the

Operator’s Manual

. Such routine maintenance,

whether performed by a dealer or by you, is at your expense. Parts
scheduled for replacement as required maintenance (“Maintenance Parts”),
are warranted for the period of time up to the scheduled replacement time

for that part. Failure to perform required maintenance and adjustments can
be grounds for disallowing a warranty claim.

Items and Conditions Not Covered

Not all product failures or malfunctions that occur during the warranty period
are defects in materials or workmanship. This express warranty does not
cover the following:

Product failures which result from the use of non-Toro replacement
parts, or from installation and use of add-on, modified, or unapproved
accessories

Product failures which result from failure to perform required
maintenance and/or adjustments

Product failures which result from operating the Product in an abusive,
negligent or reckless manner

Parts subject to consumption through use unless found to be defective.
Examples of parts which are consumed, or used up, during normal
product operation include, but are not limited to, belts, wipers, spark
plugs, tires, filters, gaskets, wear plates, seals, O-rings, drive chains,
clutches.

Failures caused by outside influence. Items considered to be outside
influence include, but are not limited to, weather, storage practices,
contamination, use of unapproved coolants, lubricants, additives, or
chemicals, etc.

Normal “wear and tear” items. Normal “wear and tear” includes, but is
not limited to, worn painted surfaces, scratched decals, etc.

Repairs necessary due to failure to follow recommended fuel
procedure (consult

Operator's Manual

for more details)

Removing contaminants from the fuel system is not covered

Use of old fuel (more than one month old) or fuel which contains
more than 10% ethanol or more that 15% MTBE

Failure to drain the fuel system prior to any period of non-use
over one month

Any component covered by a separate manufacturer’s warranty

Pickup and delivery charges

General Conditions

Repair by an Authorized Servicing Outlet or Self-Service as an Authorized
Rental Customer is your sole remedy under the warranty.

Neither The Toro Company nor Toro Warranty Company is liable for
indirect, incidental or consequential damages in connection with the
use of the Toro Products covered by this warranty, including any
cost or expense of providing substitute equipment or service during
reasonable periods of malfunction or non-use pending completion of
repairs under this warranty. All implied warranties of merchantability
and fitness for use are limited to the duration of this express warranty.
Some states do not allow exclusions of incidental or consequential
damages, or limitations on how long an implied warranty lasts, so the
above exclusions and limitations may not apply to you.

This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.

Except for the engine warranty coverage and the Emissions warranty
referenced below, if applicable, there is no other express warranty. The
Emissions Control System on your Product may be covered by a separate
warranty meeting requirements established by the U.S. Environmental
Protection Agency (EPA) or the California Air Resources Board (CARB).
Refer to the California Emission Control Warranty Statement supplied with
your Product or contained in the engine manufacturer’s documentation for
details.

Countries Other than the United States or Canada

Customers who have purchased Toro products outside the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee
policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee
information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.

Australian Consumer Law:

Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro

Dealer.

374-0288 Rev C

 

Summary of Contents for 23135













Reviews: