background image

 17 

 

Figure 35 is an example of tire wear caused by under 
inflation. 

 

Figure 35 

 

1. Under inflated tire

 

Figure 36 is an example of tire wear caused by over 
inflation. 

 

Figure 36 

1. Over inflated tire

 

Storage

  

For storage over 30 days, prepare the unit as follows: 
1. Remove dirt and grime from the external parts of the 

entire unit, especially the engine. Clean dirt and wood 
chips from the outside of the engine cylinder head fins 
and blower housing.

 

2. Add a petroleum based stabilizer/conditioner to fuel in 

the tank. Follow mixing instructions from stabilizer 
manufacturer. (1 oz per US gallon). 

Do not use an 

alcohol based stabilizer (ethanol or methanol). 

 

NOTE: 

Fuel stabilizer/conditioner is most effective when 

mixed with fresh gasoline and used at all times. 
 
3. Run the engine to distribute conditioned fuel through the 

fuel system (5 minutes). 

4. Stop the engine, allow it to cool and drain the fuel tank 

using a pump type siphon. Dispose of fuel properly. 
Recycle as per local codes. 

 

IMPORTANT: 

Do not store stabilizer/conditioned gasoline 

over 90 days. 

 

5. Restart the engine and run it until it stops. 
6. Choke the engine. 
7. Start and run the engine until it will not start again. 
8. Change the fuel filter; refer to Changing the Fuel Filter. 
9. Service the air cleaner; refer to Servicing the Air Cleaner. 
10. Service the engine oil and filter; refer to Changing the 

Engine Oil and Filter. 

11. Remove the spark plugs and check the condition; refer 

to Servicing the Spark Plug. 

12. With the spark plugs removed from the engine, pour two 

tablespoons of engine oil into each spark plug hole. 

13. Place rags over the spark plug holes to catch any oil 

spray, then use the starter to crank the engine and 
distribute the oil inside the cylinder. 

14. Install the spark plugs, but do not install the wires on the 

spark plugs. 

15. Check and tighten all bolts, nuts, and screws. Repair or 

replace any damaged parts. 

16. Paint all scratched or bare metal surfaces. Paint is 

available from your Authorized Service Dealer. 

17

Store the unit in a clean, dry garage or storage area. 

18. Cover the unit to protect it and keep it clean. 

Summary of Contents for 22604





















Reviews: