background image

This product complies with all relevant European
directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.

WARNING

CALIFORNIA

Proposition 65 Warning

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

Introduction

The 4-in-1 bucket is a load-bearing attachment
intended to be used on a Toro compact tool carrier.
Using this product for purposes other than its intended
use could prove dangerous to you and bystanders.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.

Visit www.Toro.com for product safety and operation
training materials, accessory information, help finding
a dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.

Figure 1

identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

Important:

With your mobile device, you can

scan the QR code on the serial number decal (if
equipped) to access warranty, parts, and other
product information.

g305274

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(

Figure 2

), which signals a hazard that may cause

serious injury or death if you do not follow the
recommended precautions.

g000502

Figure 2

Safety-alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

2

Contact us at www.Toro.com.

Printed in the USA

All Rights Reserved

 

Summary of Contents for 22478

















Reviews:

Related manuals for 22478