background image

Safety and Instructional Decals

Important:

Safety and instruction decals are located near areas of potential danger. Replace damaged decals.

Manufacturer's Mark

1.

Indicates the blade is identified as a part from the original
machine manufacturer.

112-8760

1.

Thrown object hazard—keep bystanders a safe distance
from the machine.

2.

Cutting/dismemberment of hand or foot—stay away from
moving parts.

114-3415

130-6722

1.

Attention—read the

Operator's Manual

.

116-7583

1.

Warning–Read the Operator’s Manual. Do not operate this
machine unless you are trained.

4.

Cutting/dismemberment hazard of hand or foot, mower
blade—stay away from moving parts; keep all guards in place.

2.

Thrown object hazard—keep bystanders a safe distance from
the machine.

5.

Warning—wear hearing protection.

3.

Thrown object hazard—Do not operate the mower without the
rear discharge plug or bag in place.

6.

Cutting/dismemberment hazard of hand or foot, mower
blade—Do not operate up and down slopes; operate side to
side on slopes; stop the engine before leaving the operating
position—pick up objects that could be thrown by the blades;
and look behind you when backing up.

6

Summary of Contents for 22293





























Reviews: