background image

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure

Description

Qty.

Use

1.

No parts required

Unpack the lawn mower.

2.

No parts required

Install the handle.

3.

No parts required

Install the starter rope.

4.

No parts required

Adjust the handle height.

5.

No parts required

Assemble the grass bag.

6.

No parts required

Fill the engine with oil.

Note:

Determine the left and right sides of the machine from the normal operating position.

1. Unpacking the Lawn Mower

Procedure

1. Carefully remove the lawn mower from the box.

Folding or unfolding the handle improperly can
pinch, stretch, or damage one or more of the
cables. Any pinched, stretched, or damaged
cable may cause an operational failure that
results in an unsafe operating condition.

Do not pinch, stretch, or damage the cables.

Handle the cables with care when folding or
unfolding the handle.

Do not use the lawn mower if one or more
of the cables are pinched, stretched, or
damaged. Contact an Authorized Service
Dealer.

2. Lay the upper handle on the ground behind the lawn

mower with the handle label facing up.

2. Installing the Handle

Procedure

1. Loosen the handle height adjustment knobs and

rotate the lower handle toward the rear of the lawn
mower until it seats into one of the handle height
settings as shown in Figure 3. To set the handle
height, refer to Adjusting the Handle Height.

Figure 3

1.

Handle knob

4.

Lower handle section

2.

Upper handle section

5.

Handle height adjustment
knob (2)

3.

Oval-head bolt

6.

Handle height settings

2. Remove the handle knobs and the oval-head bolts

from the upper handle section.

3. Install the upper handle section onto the lower

handle section with the oval-head bolts and the

5

Summary of Contents for 20817

























Reviews: