Toro 08781 Installation Instructions Manual Download Page 1

Form No. 3416-266 Rev A

Rear Remote Hydraulic Kit

Sand Pro

®

/Infield Pro

®

3040 and 5040 Traction Unit

Model No. 08781—Serial No. 315000001 and Up

Installation Instructions

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California

to cause cancer, birth defects, or reproductive harm.

WARNING

Hydraulic fluid escaping under pressure can
penetrate skin and cause injury.

Make sure that all hydraulic fluid hoses
and lines are in good condition and all
hydraulic connections and fittings are tight
before applying pressure to the hydraulic
system.

Keep your body and hands away from
pin-hole leaks or nozzles that eject
high-pressure hydraulic fluid.

Use cardboard or paper to find hydraulic
leaks.

Safely relieve all pressure in the hydraulic
system before performing any work on the
hydraulic system.

Seek immediate medical attention if fluid
is injected into skin.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.

Figure 1

identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

g220043

Figure 1

1.

Location of the model and serial numbers

Model No.

Serial No.

Note:

Determine the left and right sides of the

machine from the normal operating position.

© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3416-266* A

 

Summary of Contents for 08781





















Reviews: