background image

g364718

Figure 20

1.

53 mm (2 inches)

2.

Upper fuel level

3.

Install the cap to the fuel tank.

Checking the Engine Oil
Level

Refer to

Checking the Engine-Oil Level (page 20)

.

During Operation

During Operation Safety

General Safety

Wear appropriate clothing, including eye
protection; long pants; substantial, slip-resistant
footwear; and hearing protection. Tie back long
hair and do not wear loose clothing or loose
jewelry.

Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur.

Do not operate the machine while ill, tired, or
under the influence of alcohol or drugs.

Disengage the cutting disc and all drive clutches
before staring the engine.

Start the engine according to the instructions and
with your feet well away from the cutting disc.

Do not tilt the machine more than necessary to
start the engine, and lift only the part that is away
from you.

Shut off the engine, remove the key (if equipped),
and wait for all movement to stop before you leave
the operator’s position. Allow the machine to cool
before adjusting, servicing, cleaning, or storing it.

When you release the operator-presence control,
the engine should shut off and the cutting
disc should stop within 3 seconds. If not, stop
using your machine immediately and contact an
Authorized Service Dealer.

Keep bystanders, especially children and pets, out
of the operating area. Keep small children out of
the operating area and under the watchful care
of a responsible adult who is not operating the
machine. Stop the machine if anyone enters the
area.

Operate the machine only in good visibility and
appropriate weather conditions. Do not operate
the machine when there is the risk of lightning.

Wet grass or leaves can cause serious injury if you
slip and contact the cutting disc. Avoid mowing in
wet conditions if possible.

Use extreme care when approaching blind
corners, shrubs, trees, or other objects that may
block your view.

Watch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could cause you
to lose your balance or footing.

If the machine strikes an object or starts to
vibrate, immediately shut off the engine, wait for
all moving parts to stop, and disconnect the wire
from the spark plug before examining the machine
for damage. Make all necessary repairs before
resuming operation.

Never pick up or carry the machine while the
engine is running.

If the engine has been running, it will be hot and
can severely burn you. Keep away from the hot
engine.

Engine exhaust contains carbon monoxide, which
is lethal if inhaled. Do not run the engine indoors
or in an enclosed area.

Use accessories and attachments approved by
Toro only.

Slope Safety

Slopes are a major factor related to loss of
control accidents, which can result in severe injury
or death. You are responsible for safe slope
operation. Operating the machine on any slope

12

 

Summary of Contents for 02616





























Reviews: