background image

8

  BEFORE USE

1. Before using this product, read the owner's manual completely and familiarize yourself thoroughly with the 

product and the hazards associated with its improper use.

2. Perform the air purge procedure. (See System Purge Procedure.)

3. Check and that the pump operates smoothly before putting into service.

4. Inspect before each use. Do not use if bent, broken or cracked components are noted.

WARNING: Improper use of this jack may result in serious injury or death.

  OPERATION

1.  Block the vehicle’s wheels for lifting stability. 

Secure the load to prevent inadvertent shifting 

and movement.

2.  Position the jack near desired lift point.

3.  Refer to the vehicle manufacturer owner’s manual 

to locate approved lifting points on the vehicle. 

Position the jack so that the saddle is centered 

and will contact the load lifting point firmly.

4.  Assemble the handle, ensuring that it aligns with 

slots.

5.  Close the release valve by turning the handle 

knob counter-clockwise until firm resistance is felt 

and put down it.

6.  Before raising the vehicle double check and verify 

the saddle is centered and also has full contact 

with the lifting point. 

7.  Pump handle to lift until saddle contacts load. 

Continue to pump the jack handle to lift the 

vehicle to the desired height. After lifting, support 

the load with appropriately rated vehicle support 

stands before working on the vehicle. 

RAISING THE JACK

CAUTION: 

NEVER WIRE, CLAMP OR 

OTHERWISE DISABLE THE LIFT CONTROL 

VALVE TO FUCTION BY ANY MEANS 

OTHER THAN BY USING THE OPERATOR'S 

HAND. USE THE HANDLE PROVIDED WITH 

THIS PRODUCT OR AN AUTHORIZED 

REPLACEMENT HANDLE TO ENSURE 

PROPER RELEASE VALVE OPERATION. DO 

NOT USE EXTENSIONS ON THE OPERATING 

HANDLE.

1

2

Summary of Contents for BIG RED T820028DS


















Reviews: