TopXGun T1-A User Manual Download Page 1 | Manualshive

Page: 1 / 27

background image

Copyright

©

Shanghai TopXGun robotics Co., Ltd.

1

T1-A

User Manual V1.2

2016.07.20 Revision

For Firmware Version V4.10 or above

& Assistant Software Version V1.20 or above

Please strictly follow these steps to mount and use this product, as well as to install the Assistant Software on
your computer or phone.

Thank you for purchasing TopXGun product. There are web pages of T1 at our website

www.topxgun.com

is updated regularly. You can obtain product information, technical updates and manual corrections. TopXGun
recommends you to download and use the newest user manual. The information contained in this manual is
subject to change without notice.

This manual is only for basic assembly and configuration; you can obtain more details and advanced instructions
when using the assistant software, if you find the information on software and user manual are not consistent,
the assistant software shall prevail.

1
2
3
...
»

Summary of Contents for T1-A




























Reviews:

No comments

Related manuals for T1-A

Brand: GE Pages: 2

Brand: XOXO Modular Pages: 13

Brand: Saitek Pages: 13

Brand: Balboa Water Group Pages: 28

Brand: UE Pages: 4

Brand: KAR-TECH Pages: 28

Brand: 2M Technology Pages: 17

Brand: 2iB Pages: 5

Go!Control Panel

Brand: 2gig Technologies Pages: 78

Brand: Lakeshore Pages: 186

Brand: MAKOT Pages: 6

Brand: NEC Pages: 30

Brand: nvent Pages: 4

Brand: Festo Pages: 87

Brand: YASKAWA Pages: 12

Brand: Consort Pages: 4

Brand: OmarLift Pages: 50

Brand: M-system Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands