Vacancy Mode: Manual On
only,
automatic Off after set
time delay.
Mode
Position
INSTALLATION INSTRUCTIONS
TD0S5-
J
OCCUPANCY/VACANCY
(2-IN-1)
SENSOR SWITCH
Voltage .........................................................................
...
.
...
120VAC,60Hz
Incandescent ................................................................................
........
500W
Fluorescent
/Ballast
............................
..
500VA
@
120VAC/1000VA
@277VAC
Motor ........................................................................................
.......1
/
4
H
P
Time Delay ................................................................
.......1
5Sec to 30Mins
Light Level. .................................................................
.......
30 Lux--Daylight
Operation Temperature ......................................................
.....
32 F
�
-131 F
0
The passive infrared sensor work
s
by detecting the difference
between heat emitted from the human body in motion and the
background space. The sensor switch can turn a load on and hold it as
long as the sensor detects occupancy. After no motion is detected for the
set time delay, the load turned off automatically.
The sensor switch has
one relay (equal to single pole switch), also includes Ambient Light
Level Sensor.
C
overage
A
rea
The coverage range of the sensor switch is specified and illustrated in
Figure 1. Large objects and some transparent barriers like glass
windows will obstruct the sensor'
s
view and prevent detection,
causing the light to turn off even
if
someone is still in the detection area
.
- 01-
Figure 1
Figure 2
Figure 3
-02-
Description
OFF
Left
Circuit is permanently
opened.
( switched off)
Center
Occupancy Mode:
Automatic On, automatic
Off
after set time delay.
VAC
Right
Figure 4
P
ush-
B
utton
on Reaction
None
Manually toggles
On
I
Off load.
Manually toggles
On/Off the load.
Time Delay knob
Default position: 15 Seconds (Test mode)
Adjustable: from 15 Seconds to 30 Minutes (clockwise)
Sensor Sensitivity Range Knob
Default position: Center at 65%
Adjustable: 30% (Position 1) to 100% (Position 4)
Note:
Turn toward right for greater room space.
Turn toward left to avoid false alert in smaller room and near
the door way or heat source.
-03-
1.
2.
The black wires on the sensor are hot and load interchangeable
.
Connect lead wires as wiring diagram (see Figure 2):
One B
lack
lead
to
Hot or Load,
The other Black
lead to
Load or Hot
, Green
lead to Ground.
3.
Gently position wires in wall box, attach sensor switch to the box.
4.
Mount device "TOP"
up.
5.
Restore power at circuit breaker or fuse
.
W
ait
three
minute
s for
the sensor complete its initial run.
Note:
The sensor needs to be charged for 3 minutes in the first
use. Please do not press any button and make any adjustment in
this period of them for the sensor to work properly.
6.
Remove the small cover plate. (Illustrated
in
Figure 3)
7.
Locate the adjustment knobs on the control panel to test
and
change setting
.(
I
llustrated
in
Figure 3)
8.
Replace the small cover plate after testing and
setting
.
9.
Attach the wallplate.
DESCRIPTION
ION
I
INSTALLATION
ION
SAFETY WARNING:
:
Read and understand these instructions
before installation. This device is intended for installation in
accordance with the National Electrical Code and local
regulations.
I
t is recommended that a qualified electrician
perform this installation. Make sure to turn off the circuit
breaker or fuse(s) and test that the power is off before wiring
the device.
Note:
Green wire on the sensor must be connected to Ground
or Neutral for the sensor to work proper
l
y.
W
iring Diagram:
ADJUSTMENT
Band Switch
D
escription
OCC
TDOS5-
J
SPECIFICATIONS
A
mbient
Light
L
evel
Adjustment
.
Note:
Please complete Initial Run (3 minutes) before adjusting
ambient light level
.
1.
Set the Band Switch to VAC.
Switch Type .......................................................
.
.........................Single Pole
