manualshive.com logo in svg

Topcon LN-100, Instruction Manual

Share
Download
Topcon LN-100 Instruction Manual Download Page 17

14

5. PREPARATION

Installing the battery

Mount the charged battery.

• Use the attached battery (BDC70).
• When installing/removing the battery, make sure that moisture or dust particles do not come in 

contact with the inside of the instrument.

• Be careful not to shut the battery cover on your fingers.
• Before removing the battery, turn off the power to the instrument. If the battery is removed while the 

power is switched on, a warm boot may occur. File and folder data may be lost as a result.

• Do not open the battery cover while the power is on.
• Remove batteries from the surveying instrument or charger before putting into storage.

PROCEDURE

1. Push the catch on the battery cover upwards 

to open the cover.

2. Check the orientation of the terminal of the 

battery, and then insert the battery by sliding it 
to the right and pressing against the main unit.

• Do not insert the battery diagonally, as this 

may damage the main unit or the battery 
terminal.

3. Close the battery cover. 

Make sure it clicks.

Summary of Contents for LN-100






































Reviews:

No comments

Brands by name

Popular brands

Load more brands