manualshive.com logo in svg

Topcon IS-5000, User Manual, Page: 2 / 16

Share
Download
Topcon IS-5000 User Manual Download Page 2

i  

2031005555 Revision B, 04/14

 

 

Thank you for purchasing the TOPCON IS-5000 Instrument Stand. 
  
The IS-5000 stand is a reliable standard for Ophthalmic and Optometric instrument delivery and will 
provide many years of service.  
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 

 
Please read this user's manual carefully in order to familiarize yourself with and to obtain the best 
performance from your system. Place the manual in a convenient location for future reference. 
 

 
PRECAUTIONS 

 

1.

 

Installation. Never position the unit where it will be exposed to moisture, direct sunlight, dust, 
salty air, chemical storage areas, excessive temperature or humidity. Install the unit in a stable 
place, free of uneven floors, vibration and shock. 

 
2.

 

Prior to operation. Always check that all the cords are properly connected. 

 
3.

 

Operation. Take the proper steps to stop the unit (leaving the patient in a safe condition) if 
anything is found wrong with the unit. 

 
4.

 

After Operation. Never hold and pull the connecting cord for disconnecting plugs. Excessive 
force may be applied and cause damage to the inside connections. If the unit has not been used 
for a long period of time, check the operation and safety features prior to using it again. 

 
 

SAFETY CONCERNS 

 

The IS-5000 Stand conforms to UL 60601-1 and CSA C22.2 No. 601.1-M90. Any of the optional 
equipment defined in this manual can be added to the IS-5000 without introducing any additional 
safety hazards. 

 
 

WARNING

:  The installation of the IS-5000 stand shall only be performed by a 

qualified technician. 

 

WARNING

:  The IS-5000 stand is designed for usage with TOPCON equipment. 

If any other equipment is used, it shall meet the same certifications. 

 

WARNING

:  All service (except replacing the two external fuses) and repairs 

shall be performed by a qualified technician. 

 

WARNING

:  All replacement parts or optional equipment shall be genuine 

Topcon parts. Contact Topcon or your dealer for those items. 

 

!

 

!

 

!

 

!

 

Summary of Contents for IS-5000

















Reviews:

No comments