background image

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

Entire Contents © Copyright 2009

TOPA0703 Mnl V1.0

WARRANTY

Top Flite Models guarantees this kit to be free from defects in both material and workmanship at the date of 
purchase. This warranty does not cover any component parts damaged by use or modification. In no case 
shall Top Flite’s liability exceed the original cost of the purchased kit.
 Further, Top Flite reserves the 
right to change or modify this warranty without notice.

In that Top Flite has no control over the final assembly or material used for final assembly, no liability shall be 
assumed nor accepted for any damage resulting from the use by the user of the final user-assembled prod-
uct. By the act of using the user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is 
advised to return this kit immediately in new and unused condition to the place of purchase.

To make a warranty claim send the
defective part or item to Hobby
Services at this address:

Include a letter stating your name, return shipping address, as much contact information as possible (daytime 
telephone number, fax number, e-mail address), a detailed description of the problem and a photocopy of the 
purchase receipt. Upon receipt of the package the problem will be evaluated as quickly as possible.

Hobby Services
3002 N. Apollo Dr. Suite 1
Champaign IL  61822  USA

SPECIFICATIONS

Wingspan:

85 in
[2160mm]

Wing

Area:

1329 sq in
[85.7 dm

2

Weight:

19.5 – 21.5 lb
[8842– 9749 g]

Wing

Loading:

34– 37 oz/sq ft
[104–113 g/dm

2

]

Length:

75 in
[1905mm]

Radio:

5-7 channel

Engine:

2.6–4.0 cu in
[43–65cc] spark ignition gas

[email protected]

Top Flite Models  Champaign, IL

Telephone (217) 398-8970, Ext. 5

Summary of Contents for P-47D Thunderbold





































Reviews: