background image

12

COMPUTER INSTRUCTIONS 

The monitor can only be power on with using the AA batteries. 

FUNCTION BUTTONS 

MODE   
1. Press the button to select TIME, DISTANCE and CALORIES to preset.
2. Press the button for selection function display value on LCD, or enter after setting.

3. Press the button and hold for 2 seconds to reset all value except Odometer to be zero.

(When the user replace batteries, all the values will reset to ZERO automatically.)

SET 
1. To set up the target value of TIME, DISTANCE and CALORIES.
2. Press the button and hold for 2 seconds to speed up the increment.

RESET 
1. Press the button to reset function value when setting.
2. Press the button and hold for 2 seconds to reset all value except Odometer to be zero.

(When the user replace batteries, all the values will reset to ZERO automatically.)

FUNCTIONS & OPERATIONS 

Time 

Accumulates  total  time  from  00:00  up  to  99:59.  The  user  may  preset  target  time  by 
pressing SET & MODE button. Each increment is 1 minute. 

Automatically count down from targeting value during exercise. 

Calories 

Accumulates calories consumption during training from 0 to max. 9999 calories. The user 
may also preset the target calorie before training by press SET & MODE 

button.  Each 

setting increase is 1 cal till 1000, Each increment will be 10 cal when calories is over 1000. 

Automatically count down from targeting value during exercise. 
Note : This data is a rough guide which can not be used in medical treatment 

Summary of Contents for BRX60














Reviews: