Page 2
593073 AUTOMATIC HOSE REEL
INSTRUCTION MANUAL
FEATURES
This Toolex Industrial Hose Reel is made of high-quality materials. It is driven and released by a coiled
spring, which can rewind the hose automatically.
Developed and designed for multi-purpose use, this reel has the following features:
• Automatic locking - the hose will automatically lock every 1 metre (approx.) of extended hose.
• Self layering system - smooth coiling system.
• Reinforced PVC braided hose with 2 metre leader hose pre-fitted.
• Industrial strength high impact plastic case provides secure storage.
• Swivel mounting bracket for versatility and 180º rotation.
• Carry handle enables easy moving between selected mountings.
• Ideal for industrial and automotive sites, mobile and home workshops, plumbing and carpentry.
• Suitable for compressed air applications only.
This reel is fitted with a high quality kink resistant PVC braided hose 20m length.
This reel is complete with 2m leader hose, mounting bracket, metal tube and 4 x M8 expansion
bolts. The industrial-strength metal tube connects the reel to the mounting bracket.
This reel can be fixed on a wall or ceiling using the mounting bracket.
INSTALLATION
This Toolex Industrial Hose Reel can be mounted
in a horizontal or vertical position.
1. Choose a location that is near to the air source.
2. For large areas, place the hose reel at the centre
of the work area.
3. When mounting the hose reel vertically, ensure there is
adequate clearance under the reel to prevent injury
or damage.
4. Install the mounting bracket onto a flat surface.
Note: It is recommended to install the mounting bracket
0.8m (minimum) above the floor level.
a) Drill 4 x M8 holes to match the holes located in the
mounting bracket.
b) Push the 4 x M8 expansion bolts (supplied) into the holes
and secure the mounting bracket using the washers
and nuts.
5. Connect the hose reel to the mounting bracket
with the metal tube.
6. Connect the inlet leader hose to the air source.
Apply thread sealing tape to all air line and air fittings.
Operating
Instructions
FEATURES
This JFlex Hose Reel is made of
high-quality materials. It is driven and
released by a coiled spring, which can
rewind the hose automatically.
Developed and designed for multi-purpose
use, this reel has the following features:
• Automatic locking - the hose will
automatically lock every 1 metre (approx.)
of extended hose.
• Self layering system - smooth coiling system.
• Reinforced PVC braided hose with 2 metre
leader hose pre-fitted.
• Industrial strength high impact plastic case
provides secure storage.
• Swivel mounting bracket for versatility and
180º rotation.
• Carry handle enables easy moving between
selected mountings.
• Ideal for industrial and automotive sites,
mobile and home workshops, plumbing
and carpentry.
• Suitable for compressed air applications only.
This reel is fitted with a high quality kink
resistant PVC braided hose 20m length.
This reel is complete with 2m leader hose,
mounting bracket, metal tube and 4 x M8
expansion bolts. The industrial-strength metal
tube connects the reel to the mounting bracket.
This reel can be fixed on a wall or ceiling using
the mounting bracket.
INSTALLATION
This JFlex Hose Reel can be mounted in a
horizontal or vertical position.
1. Choose a location that is near to the
air source.
2. For large areas, place the hose reel at the
centre of the work area.
3. When mounting the hose reel vertically,
ensure there is adequate clearance under the
reel to prevent injury or damage.
4. Install the mounting bracket onto a flat surface.
Note: It is recommended to install the
mounting bracket 0.8m (minimum) above the
floor level.
20M
RETRACTABLE
AIR HOSE REEL
0.8 metre
Ground
W
all
58.1067-HoseReel_manual.indd 1
6/03/12 1:26 PM
a) Drill 4 x M8 holes to
match the holes located
in the mounting bracket.
b) Push the 4 x M8
expansion bolts
(supplied) into the holes
and secure the mounting
bracket using the
washers and nuts.
5. Connect the hose reel
to the mounting bracket
with the metal tube.
6. Connect the inlet leader
hose to the air source.
Apply thread sealing
tape to all air line and
air fittings.
OPERATION
1. Slowly pull out the hose to the required
length. A ‘clicking’ noise will be heard every
revolution of the inner drum. To lock the reel,
allow the hose to retract slowly after hearing
the second or third ‘click’.
2. To release the hose, pull out the hose until
the ‘clicking’ noise stops, and then allow the
hose to slowly retract.
WARNING
To avoid injury and damage, always hold the
hose while it is retracting.
MAINTENANCE
• Always keep the hose clean. If the hose
becomes dirty, clean it with a damp cloth
while retracting.
• Mount the hose reel in a sheltered area to
assist and protect the performance of the
hose and reel.
• DO NOT allow the hose to contact any
corrosive chemicals or fluids.
• Always retract the hose when not in use.
• This JFlex Hose Reel contains a
pre-tensioned spring inside the drum assembly.
• DO NOT attempt to open the drum assembly.
• If the hose jams, pull the hose fully out and
retry. Repeat procedure if required.
• Always guide hose back into the reel and
ensure the hose is clean and not twisted.
JFLEX
Distributed by Primus Australia Pty Ltd.
Bundoora VIC 3083
SPECIFICATIONS
Part No. Hose
Length
Hose
Material Working Pressure
Hose
I.D.
Hose
O.D.
Leader Hose
Length
Size of Inlet
58.1067 20m
PVC
Max.250p.s.i.(17Mpa) 9.5mm 16mm 2m
1/4” BSP
58.1067-HoseReel_manual.indd 2
6/03/12 1:26 PM
a) Drill 4 x M8 holes to
match the holes located
in the mounting bracket.
b) Push the 4 x M8
expansion bolts
(supplied) into the holes
and secure the mounting
bracket using the
washers and nuts.
5. Connect the hose reel
to the mounting bracket
with the metal tube.
6. Connect the inlet leader
hose to the air source.
Apply thread sealing
tape to all air line and
air fittings.
OPERATION
1. Slowly pull out the hose to the required
length. A ‘clicking’ noise will be heard every
revolution of the inner drum. To lock the reel,
allow the hose to retract slowly after hearing
the second or third ‘click’.
2. To release the hose, pull out the hose until
the ‘clicking’ noise stops, and then allow the
hose to slowly retract.
WARNING
To avoid injury and damage, always hold the
hose while it is retracting.
MAINTENANCE
• Always keep the hose clean. If the hose
becomes dirty, clean it with a damp cloth
while retracting.
• Mount the hose reel in a sheltered area to
assist and protect the performance of the
hose and reel.
• DO NOT allow the hose to contact any
corrosive chemicals or fluids.
• Always retract the hose when not in use.
• This JFlex Hose Reel contains a
pre-tensioned spring inside the drum assembly.
• DO NOT attempt to open the drum assembly.
• If the hose jams, pull the hose fully out and
retry. Repeat procedure if required.
• Always guide hose back into the reel and
ensure the hose is clean and not twisted.
JFLEX
Distributed by Primus Australia Pty Ltd.
Bundoora VIC 3083
SPECIFICATIONS
Part No. Hose
Length
Hose
Material Working Pressure
Hose
I.D.
Hose
O.D.
Leader Hose
Length
Size of Inlet
58.1067 20m
PVC
Max.250p.s.i.(17Mpa) 9.5mm 16mm 2m
1/4” BSP
58.1067-HoseReel_manual.indd 2
6/03/12 1:26 PM
a) Drill 4 x M8 holes to
match the holes located
in the mounting bracket.
b) Push the 4 x M8
expansion bolts
(supplied) into the holes
and secure the mounting
bracket using the
washers and nuts.
5. Connect the hose reel
to the mounting bracket
with the metal tube.
6. Connect the inlet leader
hose to the air source.
Apply thread sealing
tape to all air line and
air fittings.
OPERATION
1. Slowly pull out the hose to the required
length. A ‘clicking’ noise will be heard every
revolution of the inner drum. To lock the reel,
allow the hose to retract slowly after hearing
the second or third ‘click’.
2. To release the hose, pull out the hose until
the ‘clicking’ noise stops, and then allow the
hose to slowly retract.
WARNING
To avoid injury and damage, always hold the
hose while it is retracting.
MAINTENANCE
• Always keep the hose clean. If the hose
becomes dirty, clean it with a damp cloth
while retracting.
• Mount the hose reel in a sheltered area to
assist and protect the performance of the
hose and reel.
• DO NOT allow the hose to contact any
corrosive chemicals or fluids.
• Always retract the hose when not in use.
• This JFlex Hose Reel contains a
pre-tensioned spring inside the drum assembly.
• DO NOT attempt to open the drum assembly.
• If the hose jams, pull the hose fully out and
retry. Repeat procedure if required.
• Always guide hose back into the reel and
ensure the hose is clean and not twisted.
JFLEX
Distributed by Primus Australia Pty Ltd.
Bundoora VIC 3083
SPECIFICATIONS
Part No. Hose
Length
Hose
Material Working Pressure
Hose
I.D.
Hose
O.D.
Leader Hose
Length
Size of Inlet
58.1067 20m
PVC
Max.250p.s.i.(17Mpa) 9.5mm 16mm 2m
1/4” BSP
58.1067-HoseReel_manual.indd 2
6/03/12 1:26 PM