• Safe operation is no longer guaranteed when:
- the product shows obvious damage
- the product does not work properly or at all
(flickering light, emitting smoke or smell of
burning, audible crackling noise, discoloration
of the product or adjacent surfaces)
- the power supply was stored for an extended
period under adverse conditions or
- if the product was damaged during transport.
• Always disconnect the mains plug from the wall
socket before cleaning or when not using the
product for a longer period of time (e.g. when
storing).
• If you have any further questions that have not
been considered in these operating instructions,
please contact us or any other expert.
Operation
•
Place the magnifier lamp on a horizontal, flat, stable and adequately big surface, e.g. on a desk.
Protect valuable furniture surfaces with a suitable pad to prevent scratching, denting or staining.
• Plug the power adapter into a properly installed household power outlet.
•
To turn on/off the magnifier lamp, set the on/off switch located on the top of the base accordingly (“I” =
On, “O” = Off).
• Adjust the lamp head as desired.
•
In order to use the magnifier, flip the hinged lid upwards.
When not using the magnifier, always cover it with the hinged lid. Otherwise there is a risk of fire
when exposed to sunlight, since the magnifier has the same effect as a burning lens.
•
You may use the trays or openings on the top of the magnifier lamp for storing small components or pens.
Securing the lamp base
• When moving the lamp base regularly, the mounting screw could
loosen.
•
Use the small hexagon wrench located in the bottom of the base to
retighten the respective hexagon screw of the lamp base.
Maintenance and care
Do not apply too much pressure to the product’s surfaces as this may cause scratching. This
especially applies to the magnifier.
• The product does not require any maintenance, do not disassemble it. Have maintenance or repair
services done by a specialist workshop only.
• The LEDs are permanently installed and non-replaceable.
• Disconnect the product from the mains before cleaning; unplug the plug-in socket from the mains socket.
• Clean the exterior of the product using a clean, soft, dry cloth only. Do not use any aggressive cleaning
agents or chemical solutions as these may damage the housing causing discoloration and/or malfunc-
tion.
• Dust can be easily removed with a clean, soft brush and vacuum air.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical Data
Operating voltage ................................. 220 – 240 V/AC, 50 Hz
Power consumption .............................. 6 W
Protection class .................................... II
Illuminant .............................................. 72 LEDs (non-replaceable)
Light colour ........................................... 6000 - 7000 K (cold-white)
Luminous flux
....................................... 400 lm
Magnification of magnifier
..................... 1.75 x(3 diopter)
Diameter of magnifier
........................... 127 mm
Pivoting range of lamp head ................. 270°
Ambient conditions ............................... Temperature -20 °C to +40 °C, relative humidity 0% to 90%, non-
condensing
Cable length ......................................... approx. 1.5 m
Dimensions ........................................... Lamp head: 235 x 188 x 30 mm (L x W x H)
Stand: 230 x 190 mm (L x W)
Total: 230 x 190 x 385 mm (L x W x H)
Weight .................................................. 2.5 kg
Operating Instructions
LED Magnifier Lamp 6 W
Item No. 2131497
Intended Use
The product is intended for illumination of dry, closed indoor areas, e.g. for use on desks. The large, built-in
magnifier is helpful when working with small components or similar (e.g. during SMD soldering). Various
trays and openings provide storage for small components or pens.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use
can result in short circuits, fires, electric shocks or other hazards. Read the instructions carefully and store
them in a safe place. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and prod-
uct names are trademarks of their respective owners. All rights reserved.
Delivery Content
•
Magnifier lamp
• Hexagon wrench (located in the bottom of the base, for securing the lamp arm)
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads
or scan the QR code shown.
Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your health, e.g. due to an
electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important information in
these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
The product was constructed according to protection class II.
The product may be set up and used only in dry, closed indoor spaces. The product must not get
moist or wet. There is a risk of fatal electric shock!
Safety Instructions
Read the operating instructions
carefully and especially observe
the safety information. If you do not
follow the safety instructions and
information on proper handling in
this manual, we assume no liability
for any resulting personal injury or
damage to property. Such cases will
invalidate the warranty/guarantee.
a) General
• Due to safety and approval concerns the prod-
uct must not be modified and/or altered without
authorization.
• The lamp is not a toy; keep away from children!
Children are not able to evaluate any dangers
that can arise when handling electric devices
improperly. Use extreme caution when children
are present.
•
There is also a risk of injury when the magnifier
lamp tips over/ falls down.
• Do not leave packaging material unattended, as
children could use it as a toy creating hazardous
situations.
• For installations in industrial facilities, follow the
accident prevention regulations for electrical sys-
tems and equipment of the government safety
organization or the corresponding authority for
your country.
b) Attention, LED light:
• Do not look directly into the LED light!
• Do not look into the beam directly or with optical
instruments!
c) Operation
• The product may be set up and used only in
dry, closed indoor spaces. The product must not
get moist or wet. There is a risk of fatal electric
shock!
• Never connect or disconnect the mains plug with
wet hands.
• Do not use the product in rooms or under ad-
verse ambient conditions, where combustible
gas, smoke or dust are or could be present!
There is a risk of explosion!
• Protect the product from extreme temperatures,
strong vibrations or strong mechanical stress.
• Never use the product immediately after it has
been brought from a cold room into a warm one.
The condensation generated could destroy the
product. There is also a risk of lethal electric
shock!
• Allow the device to reach room temperature
before connecting and using it. This may take
several hours.
• Never pour liquids above or near the product.
• Never place the product on an unstable or mov-
ing surface. Install the magnifier lamp in such a
way that it cannot tip over or fall down. Choose a
horizontal, flat and stable surface.
• Tipping over/ falling down could cause injuries
and on top of that will damage the product.
• Connect the power adapter to a wall socket that
can be accessed easily.
• Do not pull the cable when disconnecting the
mains plug from the wall socket.
• Protect the mains cable from sharp objects or
edges. Route the cable in such a way that it does
not present any trip hazards.
• Never carry the product by its cable.
• Do not hang any objects (e.g. decorative materi-
als) on the magnifier lamp.
•
Do not use the magnifier lamp to look into bright
light sources; there is a risk of eye injury.
•
When not using the magnifier, always cover it
with the hinged lid. Otherwise there is a risk of
fire when exposed to sunlight, since the magni
-
fier has the same effect as a burning lens.
• Disconnect the wall socket to which the product
is connected on all poles (turn off the respective
safety device or unscrew the fuse, and then turn
off the ground fault circuit interrupter). Do only
then disconnect the mains plug from the wall
socket.
• Should a safe operation of the product be no
longer possible, take the product out of operation
and secure it against accidental use.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
*2131497_v1_0619_02_dh_m_en
