manualshive.com logo in svg

TOOLCRAFT LDM X100, Operating Instructions Manual

Share
Download
TOOLCRAFT LDM X100 Operating Instructions Manual Download Page 27

•  Press the camera button again to switch between two- 

and four-time magnification.
The magnification factor is shown in the top right of the 

display.

•  Once you have targeted the measuring point, make your 

measurements as usual.

 Any ongoing measurement (e.g. volume 

measurement) is not affected. Previously 

registered values are retained in the buffer.

24. Data export (only LDM X100)

  As soon as the product is connected to a computer, 

the charging process starts.

 

If you operate the product with conventional, 

non-rechargeable batteries, remove them before 

connecting the product to a computer.

•  Connect the product with the included cable to your 

computer.
The product is shown as a drive with the name “Laser-

Meter".

•  On  the  drive,  there  is  a  file  named  “DISTANCE.CSV". 

Copy the file in your desired directory.

•  Safely eject the product via the operating system before 

you disconnect the cable.

27

Summary of Contents for LDM X100


































Reviews:

No comments

Brands by name

Popular brands

Load more brands