Operating Elements
1
2
3
4
5 6 7
8
9
1 Soldering iron tip
2 Protective barrel
3 Heating element (internal)
4 Cap locking screw
5
Decrease button
6
Increase button
7
Power button
8 LED temperature indicators
9 Power cord
Setup
• Set the stand by gently bending the holder
up 90º.
• Latch the cap locking screw
(4)
over the edge
of the cradle.
Do not overbend or adjust the height too many times as this may break the metal.
Operation
• Connect the soldering iron power plug to a mains
power socket. The power button
(7)
LED
will flash slowly to indicate the iron is receiving
power.
• Short press the power button
(7)
to turn the
iron ON. The power
button LED will flash
rapidly to indicate that it is heating up.
- An LED temperature indicator
(8)
will light up
beside the active temperature.
- The iron will heat up to the last temperature
that was set. If the iron has been disconnected
from the power supply it will return to the
default temperature of 390°C.
• Press the
(5)
or
(6)
button to decrease or
increase the temperature.
- The higher the temperature the faster the
power
button LED will flash.
- An LED temperature
indicator
(8)
will light up
beside the active temperature.
• Short press the power button
(7)
to turn the
iron OFF. The power
button LED will flash
slowly
• Disconnect from the power socket after use. The
power button LED will go off.
a) Standby Mode
The soldering iron will enter standby mode if not
used for 10 minutes.
• The temperature will reduce to 200 ºC.
• Move the soldering iron to exit standby mode.
The iron will begin heating to the previously set
temperature.
b) Auto Shutdown
• The soldering iron will automatically shut down if
not used for 20 minutes.
• Short press the power button
(7)
to turn the
iron back ON. The power button LED will
rapidly flash to indicate it is heating up.
Maintenance and Care
• Always keep the tip tinned before switching off or
storing for any period of time.
• Never clean the tip with coarse, abrasive
materials like files.
• If oxide forms on the tip, lightly rub with abrasive
paper, wipe clean, then immediately reheat and
re-tin the tip to prevent oxidation of the wettable
surface.
• Do not use any aggressive cleaning agents,
rubbing alcohol or other chemical solutions as
they can cause damage to the housing and
malfunctioning.
Troubleshooting
Please contact technical support service or other
technical personnel if the following occurs:
• All 5 LED temperature indicators
(8)
flashing
indicates a failed heating element.
• All 5 LED temperature indicators
(8)
constantly
on indicates a problem with the heating sensor
or related circuit.
Disposal
Electronic devices are recyclable
waste and must not be disposed of in
the household waste. At the end of its
service life, dispose of the product in
accordance with applicable regulatory
guidelines. You thus fulfill your statutory
obligations and contribute to the
protection of the environment.
Technical Data
Input voltage ..................... 230 V/AC 50 Hz
Power ............................... 80 W
Temperature accuracy ...... ±10 ºC
Temperature stability ........ ± 2 ºC
Temperature unit ............... ºC
Heater ............................... 4-core PTC
Temperature settings ........ 350 °C, 370 °C, 390 °C,
450 °C, 480 °C
Heating time ..................... approx. 90 s to reach
480 °C
Time until standby ............ 10 min
Standby temperature ........ 200°C
Time until shutdown .......... 20 min
Operating conditions ......... -0 to +40 ºC
<80 % rH
(non-condensing)
Storage conditions ............ -20 to +80 ºC
<80 % rH
(non-condensing)
Power cable length ........... approx. 1.4 m
Dimensions (ø x L) ........... 27 x 230 mm
Weight .............................. 200 g
Visit the Conrad website and search
item no.
2141865
for information about
any optional accessories, spares, or
replacement parts.
Operating Instructions
Soldering Iron 230 V 80 W +350 to +480 °C
Item No. 2141865
Intended Use
The product is a soldering iron with LED temperature indicators and control buttons. A grounded power
cable provides additional safety during use. It comes with a soldering iron stand and connects directly to a
mains power outlet.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use
can result in short circuits, fires, electric shocks or other hazards. Read the instructions carefully and store
them in a safe place. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Soldering iron
• Stand
• Operating instructions
Up-to-Date Operating Instructions
Download the latest operating instructions at www.
conrad.com/downloads or scan the QR code shown.
Follow the instructions on the website.
Safety Instructions
Read the operating instructions
carefully and especially observe
the safety information. If you do not
follow the safety instructions and
information on proper handling in
this manual, we assume no liability
for any resulting personal injury or
damage to property. Such cases will
invalidate the warranty/guarantee.
a) General Information
• The device is not a toy. Keep it out of the reach
of children and pets.
• Do not leave packaging material lying around
carelessly. This may become dangerous playing
material for children.
• Protect the appliance from extreme
temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, steam and
solvents.
• Do not place the product under any mechanical
stress.
• If it is no longer possible to operate the product
safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer
be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor
ambient conditions or
- has been subjected to any serious transport-
related stresses.
• Please handle the product carefully. Jolts,
impacts or a fall even from a low height can
damage the product.
• Consult an expert when in doubt about the
operation, safety or connection of the appliance.
•
Maintenance, modifications and repairs must
only be completed by a technician or an
authorised repair centre.
• If you have questions which remain unanswered
by these operating instructions, contact our
technical support service or other technical
personnel.
b) Electrical Connection
• The mains outlet must be located near to the
device and be easily accessible.
• Never pull the mains plug from the socket by
pulling at the cable. Always pull it from the mains
socket using the intended grips.
• Unplug the mains plug from the mains socket if
you do not use the device for an extended period
of time.
• For safety reasons, always unplug the device
during thunderstorms.
• Make sure that the mains cable is not squeezed,
bent, damaged by sharp edges or put under
mechanical stress. Avoid excessive thermal
stress on the mains cable from extreme heat or
cold. Do not modify the mains cable. Otherwise
the mains cable may be damaged. A damaged
mains cable can cause a deadly electric shock.
• Do not touch the mains cable if it is damaged.
First, power down the respective mains socket
(e.g. via the respective circuit breaker) and then
carefully pull the mains plug from the mains
socket. Never use the product if the mains cable
is damaged.
• To prevent risks, damaged power cables
may only be replaced by the manufacturer,
a professional workshop appointed by the
manufacturer, or a similarly qualified person.
• Never plug in or unplug the mains plug when
your hands are wet.
• Always lay the cables so that nobody can trip
over or become entangled in them. This poses
a risk of injury.
c) Operation
• Never touch the barrel
(2)
or tip
(1)
of the
soldering iron during use. Risk of burns!
• Never use the soldering iron to heat up liquids.
• Never solder live electrical components or parts.
Always switch off the power before-hand.
• Do not cover or fasten any items to the soldering
iron. Otherwise there is a risk of fire.
• Touching or soldering capacitors (or similar
components) or leads/cables that are connected
to capacitors may cause a fatal electric shock!
Capacitors may stay charged for several hours
after you switch off the power supply!
•
Always solder on non-flammable surfaces.
Protect other materials nearby from damage
through heat.
•
Risk of fire or explosion! Do not use around or
near explosive or flammable materials.
• Turn the power off and place the soldering iron
on the stand while taking breaks or not using.
d) Work Safety
•
Ensure that there is sufficient lighting.
• Ensure proper ventilation during soldering.
Solder and flux vapours can be harmful to your
health.
• Wash your hands thoroughly after working with
solder. This is particularly important when using
lead-based solder.
• Do not put soldering alloys into your mouth. Do
not eat or drink during soldering.
• Wear suitable protective clothing and safety
goggles when soldering. Liquid/splashing solder
may cause serious burns or eye damage.
• For installations in industrial facilities, follow the
accident prevention regulations for electrical
systems and equipment of the government
safety organization or the corresponding
authority for your country.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
*2141865_v1_1019_02_dh_m_en
