background image

Radial Cabbone

www.radialeng.com

Owner’s Manual

Radial Engineering

1638 Kebet Way, Port Coquitlam BC  V3C 5W9

tel:  604-942-1001 • fax:  604-942-1010 

email:  [email protected] • web:  www.radialeng.com

Radial Engineering is a division of C•TEC (JP CableTek Electronics Ltd.)

Part # R800 7060 00

RADIAL LIMITED ONE YEAR WARRANTY 

Radial Engineering - a division of JP CableTek Electronics Ltd. (“Radial”) 

warrants this product to be free from defects in material and workmanship to 

the original owner and will remedy any such defects free of charge according 

to the terms of this warranty.  Radial will repair or replace at its option any 

defective component(s) of this product, excluding the finish, wear and tear 

on components under normal use, and the tube and footswitch (which are 

warranted for 90 days),  for a period of one (1) year from the original date 

of purchase.  In the event that a particular product is no longer available, 

Radial reserves the right to replace the product with a similar product of 

equal or greater value. To make a request or claim under this limited warranty, 

the product must be returned prepaid in the original shipping container (or 

equivalent) to Radial or to an authorized Radial repair centre and you must 

assume the risk of loss or damage.  A copy of the original invoice showing 

date of purchase and the dealer name must accompany any request for work 

to be performed under this limited warranty.  This limited warranty shall not 

apply if the product has been damaged due to abuse, misuse, misapplica-

tion, accident or as a result of service or modification by any other than an 

authorized Radial repair centre.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE 

ON THE FACE HEREOF AND DESCRIBED ABOVE. NO WARRANTIES 

WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, 

ANY IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR 

A PARTICULAR PURPOSE SHALL EXTEND BEYOND THE RESPECTIVE 

WARRANTY PERIOD DESCRIBED ABOVE OF ONE YEAR.

RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPECIAL OR 

INCIDENTAL OR CONSEQUENTIAL DAMAGES OF LOSS ARISING FROM 

THE USE OF THIS PRODUCT.  THIS WARRANTY GIVES YOU SPECIFIC 

LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY 

VARY, FROM STATE/PROVINCE TO STATE/PROVINCE.

www.radialeng.com

Radial Engineering 

1638 Kebet Way, Port Coquitlam, BC  V3C 5W9

tel:  604-942-1001  • 

fax:  604-942-1010  

email:  [email protected] 

web:  www.radialeng.com

Radial Engineering is a division of JP CableTek Electronics Ltd.

Radial Cabbone Owner’s Manual - Part # R800 9670 00  •  V1.0  05-07-

04
Specifications and appearence are subject to change without notice.

Summary of Contents for R800 7060 00













Reviews: