EN
slide the comb on the cutting head until it locks into the de-
sired position. Please note that you should work slowly and
very accurately when using the comb in order to achieve the
required cut quality.
Cleaning and maintenance
In order to ensure the full functioning and performance of
your hair clippers, you should clean and oil the device regu-
larly.
Cleaning and oiling the cutter edge: The cutter edge should
be thoroughly cleaned once a day if used regularly. Switch
off the device. Push the entire cutting edge forward away
from the hair clippers. Remove hair using the cleaning brush
or by blowing. Oil the points where the upper and lower clip-
ping blades touch using the oil included.
Never use any other products for maintenance: This oil has
been specially developed for hair clippers and designed to
not vapourise or slow down the blades.
Attaching the cutter edge: Ensure that the hair clippers are
switched off. First position the lower catch in the notches on
the device and then push the cutter edge upwards using a
swivelling movement. Do not use force. The cutter edge must
clearly lock into place.
Cleaning the device: Wipe your device occasionally using a
damp cloth and then rub dry.
Always keep the electrical charge contacts clean: If the
charge contacts on the device or on the charging station be-
come dirty, this can interrupt or inhibit the charging process.
Replacing the blade head
The blade head is subject to wear. Even if you look after the
appliance, the cutting performance will deteriorate. Once the
blade head is worn, it should be replaced. The blade head
can be ordered separately as a spare part.
NiMh
Disposal of battery
There is an NiMH battery in this electrical device.
The battery must be dismantled for disposal (see
below). The battery must under no circumstances be dis-
posed of in household waste. Spent batteries may contain
pollutants which can be harmful to the environment and to
health. Trade the battery in or hand it in to your community’s
recycling centre. Returning them is free and required by law.
All batteries are reused. This allows valuable raw materials
such as iron, zinc, or nickel to be regained.
WARNING:
Without the battery, the device may neither be connected to
the power cable nor placed in the connected charging sta-
tion. Both can lead to the destruction of the electronics.
Removing the battery (Note: Should only be done to dis-
pose of the electronic device. This destroys the machine!)
1. Completely discharge the battery.
2. Remove the cutting head (Image 1). 3. Loosen the screws
on the underside of the casing
4. Push out the inner part from below (Image 2)
5. Remove the battery
Waste from electrical devices at the end of their
service life
In the interest of everyone involved and in the spirit
of actively contributing to environmental protection: The
waste bin symbol on the product indicates that this product
may not be disposed of as household waste. Dispose of the
device at a recycling collection point for electrical devices
and electronic equipment. For further information concern-
ing the recycling of this product, please contact your local
municipal administration or your waste disposal service pro-
vider.
Warranty period
Tondeo guarantees the statutory guarantee on all device
components not subject to wear and tear for all its small
electrical devices in all EU member states. In all non-EU
states, please ask your specialist dealer. Excluded from this
guarantee are normal wear and tear (cutting blades and bat-
teries) and damage that can be attributed to incorrect opera-
tion or improper treatment of the device.
This device complies with EU regulation EMC
2014/30/EU as well as the Low Voltage Directive
2014/35/EU
Technical data
Model: ECO S+
Item number.: 32504, 32505
Power supply Model: HK-AV-050A060-EU
Input: 100–240V ~ (Universal voltage range) | 50/60 Hz
Battery: Ni-MH-type, 2x1.2 V, 750 mAh
Charging time: Approx. 6–8 hours
Usage time without charging: Approx. 60 min.
Device weight: 130 g
Comb attachment: 3/4.5/6/7.5 mm
Protection class II & III
In case of commercial use: The A-weight emission sound
pressure level is < 70dB(A).
