Tomy CLASSIC TE/M6C RP Instructions Download Page 5

•  FAULT FINDING

 

3

PAGE

3

4

3

3

3

3

3

4

GB

SOLUTION 

Check the power cable connections (including wall 
socket). 

Check the batteries have adequate charge and are 
correctly installed. 

Check the power cable connections (including wall 
socket). 

Switch the Nightlight OFF by pressing the 

 

button 

then reactivate the Baby Unit’s main function by 
pressing the   button. 

 

 

Move the Parent Unit at least 10m / 30ft away from 
the Baby Unit.

 

  

Lower the volume of the Parent Unit.

Ensure both units are adequately powered. 

Bring both units closer together and repeat the 

 

‘Set-Up’ instructions.  

Power the unit via the mains using the 

 

adaptors supplied.  

 

 

Replace the batteries. 

Increase Parent Unit volume.

Move units closer. 

Refer to Sound Activated Monitoring within this 
instruction booklet.  

Bring the units closer together avoiding enviromental 
obstructions that maybe reducing your range.

Power the unit via the mains using the adaptors 
supplied. Replace the Parent Unit batteries.

 

POSSIBLE CAUSE 

Mains power is not connected correctly.

 

Battery insertion and/or battery life issues.

 

Mains power is not connected correctly.

 

The Nightlight is being operated 
independently of the Baby Unit’s 
monitoring function (which is an 
intended feature).

 

Parent and Baby Unit are too close.

 

 
 

Loss of contact alarm. 

 
 

Low battery Parent Unit.

 

 

 

Volume on Parent Unit is set too low.

Units are out of range. 

Units are set to Sound Activated 
Monitoring mode.   

The Parent and Baby Units are too 

 

far apart.

The Parent Unit batteries are running 
low.

 

PROBLEM 

My Parent Unit will not 
switch ON. 

 

My Baby Unit will not 
switch ON.

 

The Nightlight is active 
but I cannot connect 
with the Parent Unit.

 

 
 

Parent Unit is making a 
high pitched (feedback) 
noise.

 

 

There is a continuous 
beeping noise.

 

 

My Parent Unit emits 1 
beep every minute 

 

and the   button 
flashes RED. 

I cannot hear anything 
through my Parent Unit.

And/or:

It’s only intermittent. 

The sound quality has 
decreased.

 

And/or:

 

is becoming intermittent.

•  PRÉSENTATION DE VOTRE ÉCOUTE-BÉBÉ 

UNITÉ PARENT

Affichage du niveau 

 

sonore par diodes

Molette de réglage du volume 

Entrée alimentation secteur CA

Marche/Arrêt

 

Activation au son

Interrupteur de 

 

sélection du canal

Bouton MARCHE/ARRÊT

Marche/Arrêt de 

 

la veilleuse

UNITÉ BÉBÉ

F

Microphone

Rangement du 

cordon

Interrupteur de sélection du canal

Socle/Clip ceinture

Entrée alimentation secteur CA

6

7

Summary of Contents for CLASSIC TE/M6C RP






Reviews: