background image

PLATFORM ADJUSTMENT

1.  Park

 the van on a level surface.

2.  Unlock

 the platform.

3.  Unfold

 the platform completely.

4.  Adjust 

the passenger side support arm so that the platform is 1-1/2" from level

           over a 3 foot length (Figures 3 and 4).
            

a. Remove

 the 1/2" x 3-3/4" bolt and nut.

            

b. Rotate

 the length adjuster in to lower taper or out to raise taper.

            

c. Reinstall

 the 1/2" x 3-3/4" bolt and nut.

5.  Adjust 

the driver side support arm so that both support arms carry the

            platform load equally.  Adjustment similar to passenger side.

6.  Verify 

that all bolts have been re-installed and tightened.

7.  Close

 and 

Lock

 the platform.

LEVELING PLATFORM FOR LOADING

1-1/2"

3 Foot Level

Figure 3: Platform leveling position.

Figure 4: Support arm adjustment.

Support Arm

Length Adjuster

3-3/4" Bolt

DPN: 010819                                                                                                      

 Page 11 of 28  

                                                                                          Rev 14           4-8-19

TOMMY GATE

The original

hydraulic lift

Summary of Contents for CANTILEVER Series





























Reviews: