Tomahawk Monsun 20700 Instruction Manual Download Page 17

17

ENGLISH

FLIGHT RECOMMENDATIONS

Choose a calm day for your first flight and take your time adjusting the model to your needs. Ask 

a buddy to throw the model horizontally in the air or use a glider dolly. Pull the elevator gently 

after gaining sufficient speed to climb. We whish you many nice and relaxing flights with your new 

Monsun from Tomahawk.

SAFETY WARNINGS

As the user of this product, you are solely res

-

ponsible for operating in a manner that does not 

endanger yourself and others or result in dama

-

ge to the product or the property of others.

• Always  keep  a  safe  distance  in  all  directions 

around your model to avoid collisions or injury. 

This model is controlled by a radio signal sub

-

ject to interference from many sources outside 

your control. Interference can cause momen

-

tary loss of control.

• Always  operate  your  model  in  open  spaces 

away from full-size vehicles, traffic and people.

• Always carefully follow the directions and war

-

nings for this and any optional support equip

-

ment  (chargers,  rechargeable  battery  packs, 

etc.).

• Always  keep  all  chemicals,  small  parts  and 

anything electrical out of the reach of children.

• Always avoid water exposure to all equipment 

not specifically designed and protected for this 

purpose. Moisture causes damage to electro

-

nics.

• Never place any portion of the model in your 

mouth as it could cause serious injury or even 

death.

• Never operate your model with low transmit

-

ter batteries.

• Always keep aircraft in sight and under control.

• Always use fully charged batteries.

• Always keep transmitter powered on while air

-

craft is powered.

• Always remove batteries before disassembly.

• Always keep moving parts clean.

• Always keep parts dry.

• Always let parts cool after use before touching.

• Always remove batteries after use.

• Always  ensure  failsafe  is  properly  set  before 

flying.

• Never operate aircraft with damaged wiring.

• Never touch moving parts.

Summary of Contents for Monsun 20700





















Reviews: