（＊）
In case the external power source is not fitted with current limiting function,
please use FUSE (Max. 10A).
（
FUSE is not necessary if the power source fitted with current limiting function is used.
）
TRT-2416 operation manual
Thank you for purchasing our TRT-2416. Please thoroughly read this manual. This manual is a brief version of the operation manual.
Cautions
For safety purpose, following symbols are used in this manual.
!
The case that a user may receive fatal damage, electric shock, or severe burn injury
when the product is incorrectly used
The case that a user may receive minor injury or the equipment may get damage
Verify correct wiring before turning on electricity since incorrect wiring may cause an equipment failure
or a fire. Modification of this equipment may cause malfunctioning or a fire. Do not add modification on
this equipment. If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
!
!
Wiring – If the current would be large in the output terminal (OUT 1, OUT 2) as well as in the power
terminal (DC24V
＋－
), use wire material thick enough for such current (within the current rating).
!
- Hand over this operation manual to a person who actually operates the product.
- Content of this manual may be subject to modification without prior notice.
- Do not reprint or duplicate this manual without permission.
Verification of the product
1
）
Verification of the model: Refer the model name printed in the packing
box to the order sheet.
2) Model: TRT-2416
Environmental condition
（
1
）
Service temperature/humidity range:
0-50
℃
/ 20-90 % RH
（
no dew condensation
）
（
2
）
Storage temperature/humidity range:
-20-70
℃ （
no freezing or dew condensation
）
/5-95 % RH
（
no dew condensation
）
(3) Installation environment :
1) No corrosive gases, dust, oil as well as less temperature changes.
2
）
As far away as possible from an electric noise source, and little effect from
electromagnetic field
3) A location with as few mechanical vibrations or impact as possible.
4
）
No direct sunlight
5
）
Installation category I / Pollution Degree2
!
Warning
＊
The tightening torque for the terminal block screw is as follows:
0.4N
・
m
[Input Portion]
0.49 N
・
m
[Power source / Output Portion]
0.66 N
・
m
[Main body attachment portion]
＊
If the polarity (+,
－
) is specified, be careful with its wiring.
Head office: 2-4-3 Nishihashimoto, Midori-Ku, Sagamihara-Shi, Kanagawa 252-0131 Japan
TEL: +81-42-700-2100, FAX: +81-42-700-2112
Horizontal position
Vertical position
Mounting
Attachment hole dimension
*Due to risk of electric shock, do not touch the terminals while the power is running through the unit.
*Since the unit is designed to radiate heat from the bottom, do not cover this portion with insulating materials.
* We shall not be held responsible for any damages that may occur as a result of excessive usage beyond
the ranges and specifications mentioned in this specification manual.
*Please use the unit with utmost care and safety in mind in such a way that the unit be used with some
allowance to its rating and performance, and to limit the damage to minimum in case of trouble.
*Regardless of the place of use, the unit may bring about serious effect due to aging or trouble of the unit.
It is therefore advised to install proper external protective circuits and perform regular maintenance.
*If this product is used with output current of 16A, only the external power source fitted with current
limiting function may be used.
(In case the power source is not fitted with current limiting function, please make use of the
FUSE (Max. 10A) between the power source and the unit. In this case, up to 10A can be used.)
* The parts used in the unit may change without prior notice due to procurement related consequence,
and if the parts will not have any problem in its performance.
*
（
CAUTION !! REGARDING POWER LINE SERGE)
please avoid common connection of the induced load such as relay to the power source for driving the Peltier Relay.
* When making one-on-one connection of the several Temperature Controllers to
several Peltier Relays, do not connect more than two pairs to one power source.
!
Cautions
●
When power source with current limiter is used as an external power source.
●
When using a fuse for the external power source.
Output Characteristic
Ambient Temperature - Current Characteristic
Input
Installation gradient
Mounting
Input Point
2-points (IN 1, IN 2 , GND common)
DC 12V <ON> , DC 0V<OFF>
Min. Input Time
Input Resistance
Connection Method
More than 2ms (Level Input)
2.8k
Ω
Standard
Terminal Block (M3 screw)
Input Kind
Output Point
1-point
Voltage
Output Kind
Output
Connected to Peltier Drive Output (OUT 1, OUT 2)
Output Type
ON/OFF (MOS FET Output: For Peltier Drive, with inverting function)
Output Voltage
± (DC 8
～
24V) The voltage is dependent on external power voltage,
polarity is dependent on the inverting function.
Max. Output Current
16A
（
Refer to Table of Output Characteristic
）
Connection Method
Terminal Block (M4 screw
）
Service temperature/humidity range
Storage temperature/humidity range
0-50
℃
/ 20-90 % RH
（
no dew condensation
）
-20-70
℃ （
no freezing or dew condensation
）
/5-95 % RH
（
no dew condensation
）
Base plane 0 or 90 degrees (vertically with output side in upward direction
）
Use M4 screw to attach the product.
Weight
100 g or less
External code and standard None
Isolation
Non-isolated with power circuit, non-isolated with Peltier drive circuit.
Input portion
Power portion / Output portion
*For the crimp-type terminal of Power portion / Output portion, use M4 type with
insulating sheath.
*For the crimp-type terminal of Input portion, use M3 type with insulating sheath.
Specifications
Names and Functions
External Dimension
●
(TRT-2416)
Below diagram shows the sample wiring when the product is connected to
TTM-204 Temperature Controller.
ＩＮ１
,2, GND
OUT 1,
２
Peltier drive output
DC24V(+,-)
External Power Input
●
Movement of Input (1, 2) and Output (1, 2)
※
1 The table of real value shows the input 1, 2 to be the input voltage from
the temperature controller.
ON (12V) OFF (0V) is shown to be the temperature controller output.
※
2 The table of real value shows the output 1, 2 to be the Peltier drive output polarity.
In case the <Output
１
=+
、
Output 2 =->, current flows from output 1 side to output 2 side.
※
3 Heating and cooling will change depending on the direction in which the Peltier
element is attached.
IN1
IN2
OUT1
Condition
Heating
Cooling
OFF
12V
When IN 1 is ON, the output condition <OUT 1 = +, OUT 2 =
－
>
will be retained even if the voltage of IN 2 changes.
0V
0V
12V
0V
0V
+
-
No Output
-
+
Rating
Characteristics
monitor
display
DC 0V
～
1V
5mA MAX
（
at ON
）
Output specification
MOS FET Output (for Peltier drive with polarity reversion function)
Input 1
Green LED (
φ
3mm) 1 pc. The Green LED lamp will light-up
Display
Power supply voltage
when the input from the SSR drive output of Input 2 becomes ON (12V)
DC 12V ±1V
Input current
ON voltage
DC8 – 24V±10% (permissible range)
＊
Commonly used with Peltier drive (output).
Input
Output
Red LED (
φ
3mm) 1 pc. The red LED lamp will light-up
when the input from the SSR drive output of Input 1 becomes ON (12V)
Input 2
Wiring
No Output
OUT2
Webpage: http://www.toho-inc.co.jp
E-mail : [email protected]
●
●
●
●
●
●
●
TOHO ELECTRONICS INC.
Input from the temperature controller (SSR drive output)
Input Characteristic
Voltage - Current Characteristic
OFF voltage
When IN 2 is ON, the output condition <OUT 1 =
－
, OUT 2 =
+
>
will be retained even if the voltage of IN 1 changes.
図番：
30-7524-F (
裏
)
*Base plane 0 or 90 degrees (vertically with output side in upward direction
）
*Use M4 screw to attach the product.
0
2
4
6
8
10
12
14
16
18
0
10
20
30
40
50
60
M
ax
. l
oa
d
cu
rr
en
t(
A
)
Ambient temperature(
℃
)
③
②
①
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
10
11
12
13
14
In
p
u
t
cu
rr
e
n
t[
m
A
]
Input voltage[V]
Ta=25
℃
*Kindly contact us for any questions regarding the use of heat radiator.
①
Without heat
②
Heat TRH-70(
θ
f=1.52
℃
/W)
③
Heat TRH-100(
θ
f=1.14
℃
/W)
（＊）
Not recommended
wiring example