TOHATSU VF53AS Owner'S Manual Download

Page: 80 / 99

SERVICE AND MAINTENANCE

2. Attach the cowl firmly by pulling down the

cowl latch on the rear side.

Vacuum pump strainer

Maintenance

･

Incorrect installation of the strainer may cause a vacuum leak.

Be sure to install the strainer correctly.

Refer to “Chapter 11 MAINTENANCE AFTER OPERATION”

Wash the strainer with fresh water after use.

1. Remove the vacuum pump strainer.

Turn the ring nut while pushing and

holding the strainer cup.

Strainer length: 87mm

Remove the cooling water strainer.

Turn the ring nut while pushing and

holding the strainer cup.

Strainer length: 99mm

2. Wash the strainer and the strainer cup on each.

3. After the washing, assemble the strainer cups

and strainers tightening with the ring nuts on

each.

･

When installing a strainer, pay

attention to the protrusion of the O-

ring and install it correctly.

Otherwise, a vacuum leak may

occur.

NOTE

Cooling water strainer(cup)

Vacuum pump strainer(case)

Strainer

Cooling water strainer

Vacuum pump strainer

Tighten

Loosen

NOTE

Cowl latch

１

２

３

４

５

６

７

８

９

Summary of Contents for VF53AS




































































































Search results

Summary of Contents for VF53AS

Reviews:

Related manuals for VF53AS

Brands by name

Popular brands

TOHATSU VF53AS, Owner'S Manual

Search results

Summary of Contents for VF53AS

Reviews:

Related manuals for VF53AS

Brands by name

Popular brands