background image

43

11.11. Battery Charger BC-900

11.12. AC Adapter AD-0910

Power Source 

100 – 240 V AC, 50/60 Hz (use of the supplied AC adapter)

Current Consumption

Max. 5 A DC

Charging Time 

Approx. 5 hours 

Charging Capacity

8 BP-900 batteries (optional) 

LED Indicator 

Charging status (Green: Full charge, Red: On charge), Power indicator 

Operating Temperature

0 to 40 ºC (32 to 104 ºF)

Operating Humidity

90 %RH or less (no condensation)

Finish

Case: 

Steel, black, paint

Battery receptacles:  PPO resin, black 

Dimensions

240 (w) x 70 (h) x 115 (d) mm (9.45" x 2.76" x 4.53")

Weight

Unit: 1.2 kg (2.65 lb), AC adapter: 520 g (1.15 lb)

Note: The design and specifications are subject to change without notice for improvement. 

• Accessory

AC adapter (DC cord: 1.5 m or 4.92 ft, Detachable AC cord: 2 m or 6.56 ft )  ........  1

Power Source 

100 – 240 V AC, 50/60 Hz 

Output

9 V DC, 1 A

Ripple Voltage 

100 mV (p-p)

Current Consumption

400 mA AC, Input 100 V

Cord Length

1.8 m (5.91 ft)

Plug 

RC6705, center "+" 

Operating Temperature

0 to 40 ºC (32 to 104 ºF)

Operating Humidity

90 %RH or less (no condensation)

Finish

Case: PC/ABS alloy, black 

Dimensions

47.4 (w) x 33 (h) x 86.5 (d) mm or 1.87" x 1.3" x 3.41" (excluding a power cord) 

Weight

190 g (0.42 lb)

Note: The design and specifications are subject to change without notice for improvement. 

• Accessory

AC power cord (2 m or 6.56 ft)  ...............................................................................  1

11.13. Distributor YW-1022 (2-branch distributor), YW-1024 (4-branch distributor)

Model No.

YW-1022

YW-1024

Frequency Range 

1.6 – 1000 MHz (excluding 50 – 70 MHz)

Distribution Loss

4.5 dB ±3 dB (between the Mixing 

and each Distribution terminals)

8.5 dB ±3 dB (between the Mixing 

and each Distribution terminals)

Input/Output Impedance

75 Ω

Coaxial Connector

Mixing terminal: 

BNC jack, power passing type 

(30 V DC or less, 2 A or less)

Distribution 1 and 2 terminals:

BNC jack, power passing type 

(30 V DC or less, 1 A or less) 

Mixing terminal: 

BNC jack, power passing type 

(30 V DC or less, 2 A or less)

Distribution 1 – 4 terminals:

BNC jack, power passing type 

(30 V DC or less, 1 A or less) 

Operating Temperature

–10 to +50 °C (14 to 122 ºF)

Operating Humidity

90 %RH or less (no condensation)

Finish 

ABS resin, gray 

Dimensions

75 (w) x 122 (h) x 34 (d) mm (2.95" x 4.8" x 1.34")

Weight

105 g (0.23 lb)

120 g (0.26 lb)

Note: The design and specifications are subject to change without notice for improvement. 

Summary of Contents for TS-802













































Reviews: