Toa SR-C15B Operating Instructions Manual Download Page 3

1. SAFETY PRECAUTIONS

3

When Installing the Unit

• Avoid installing or mounting the unit in unstable

locations, such as on a rickety table or a slanted
surface. Doing so may result in the unit falling
down and causing personal injury and/or property
damage.

• Refer all installation work to the dealer from whom

the speaker was purchased. Installation for flying
requires extensive technical knowledge and
experience. The speaker may fall off if incorrectly
installed, resulting in possible personal injury.

• Flying precautions. 

Be sure to follow the instructions below. Otherwise,
the suspension wires or belts may be off or snap
and the speaker may fall off, causing personal
injury.
· Check to confirm that the suspension wires and

belts are strong enough to  

· The connectors of the suspension wires and belts

must be securely linked with those of the
speaker.

· All parts and components (such as enclosures,

metal pieces, and screws) must be free from any
deformation, crack, and corrosion.

· Be sure to use screws supplied with the optional

flying hardware when installing the speaker using
such hardware.

• Install the unit only in a location that can

structurally support the weight of the unit and the
mounting bracket. Doing otherwise may result in
the unit falling down and causing personal injury
and/or property damage.

• Since the unit is designed for in-door use, do not

install it outdoors. If installed outdoors, the aging of
parts causes the unit to fall off, resulting in personal
injury. Also, when it gets wet with rain, there is a
danger of electric shock.

• Owing to the unit's size and weight, be sure that at

least two persons are available to install the unit.
Failure to do so could result in personal injury.

When Installing the Unit

• Do not use other methods than specified to mount

the bracket. Extreme force is applied to the unit
and the unit could fall off, possibly resulting in
personal injuries.

• Use nuts and bolts that are appropriate for the

ceiling's or wall's material and structure. Failure to
do so may cause the unit to fall, resulting in
material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the

bracket has no loose joints after installation to
prevent accidents that could result in personal
injury.

• Use the specified mounting bracket in combination.

Doing otherwise may cause the unit or component
to fall off, resulting in personal injury.

• Do not mount the unit in locations exposed to

constant vibration. The mounting bracket can be
damaged by excessive vibration, potentially
causing the unit to fall, which could result in
personal injury.

• Do not install the unit in indoor swimming pools or

such locations where corrosion may occur easily.
The parts deteriorate if corroded, causing the unit
to fall, which could result in personal injury.

• Be sure to read this safety instructions in this section carefully in prior to use.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or

cautions regarding safety.

• After reading, keep this manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.

WARNING

Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.

Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor injury, and/or property damage.

WARNING

CAUTION

Summary of Contents for SR-C15B

































Reviews: