background image

Standard Speaker System GS-382S

Components Configuration

SB-38S

:Low-frequency enclosure

HLS38UL-8

:Low-frequency  speaker  unit

LE-M94

:Constant directivity horn

HFD-220-8

:Compression  driver

HY-M94

:Horn mounting bracket

Note

The  HNW-800  dividing  network  is  required  when  driving  the
speaker system with passive operation.

SAORI Setting

1.  When  driving  the  speaker  system  with  multi-amplifier

operation using SAORI, set the channel divider module for a

long  delay type(IS-110DL4 and  IS-110DL2) as shown  in  the

following  diagram.  (F1  as  low-frequency  and  F2  as  high-
frequency)

2.  Since the  level  setting value  is  set to  standard  values which

are  used  the  same  type  amplifier's  output  power  for  each
band,  it may  have to  be  adjusted  according  to  the  location
and condition of the area in which it is used.

Appearance

Frequency Response(Multi-Amplifier Drive Using the SAORI)

Note
CFQ

:Crossover frequency of each filter

SLP

:Slope characteristics of each filter

24S:24dB/oct Bessel

12W:12dB/oct Butterworth

LEV

 :Output level of each band

POL

: Polarity of each band

DLY

 :Delay value of each band

HEQ

 :Horn equalizer

Suspending the GS-382S

When  suspending  the  GS-382S,  make  sure  to  suspend  the

constant  directivity  horn  to  upper  direction  using  the  optional
HY-38S suspension kit as shown in the figure.
Never suspend it to lower or horizontal direction.
For  mounting  the  HY-38S  to  the  enclosure,  refer  to  its
instruction manual.

Measured at 1  watt(at 200Hz) and 2 meters.
SPL shows the converted level into  1 W/1m.

Caution

When  suspending  this  speaker,  make  sure  to  suspend  it  after
investigating  structure  of  Installation  locations,  and  confirming

that  the  suspending  wires  or  belts  are  heavy-duty  to  this
speaker.

TOA takes no responsibility for any accidents or injuries caused

by  faulty  mounting  methods  or  poorly  selected  mounting
locations.

Make  sure  to  suspend  the  constant  directivity  horn  to
upper direction.
Never suspend it to lower or horizontal direction.

Printed in Japan

133-01-328-7A

TOA Corporation

Summary of Contents for SB-38S









Reviews: