Toa F-1522SC Instruction Manual Download Page 4

Step 3.

Connect the speaker cable to the push-in terminal. 

Tip:

Use the 600 V vinyl-insulated cable (IV or HIV wire). 
The following matching cable types are recommended:

• Solid copper wire: 

ø0.8 – ø1.6 mm (equivalent to AWG 20 – 15) 

• Stranded copper wire: 0.75 – 1.25 mm

2

(equivalent to AWG 18 – 17) 

Press fully down on the corresponding terminal button and insert the cable.

Tip

To detach the cable, press fully down on the terminal button again,
then pull the cable. 

9 mm (23/64")

5. INSTALLATION

Step 1.

Cut a ø135 mm (5 

5

/

16

") hole in the ceiling.

Use the supplied paper pattern to position and trace
the hole.

Step 2.

Mount the optional Reinforcement Ring HY-RR1 to the ceiling. (Weak ceiling mounting)

Tip:

Skip this step when the ceiling is strong (no additional hardware needed).

4

Ceiling panel

ø135 

±

5 mm (5 

5

/

16

±

13

/

64

")

A dust cover is pre-mounted on the rear of the speaker at the factory.
Pay attention not to accidentally take it off during speaker installation.

The F-1522SC ceiling speaker can be mounted in 2 different configurations:

• Direct mounting to a strong ceiling panel 

No additional hardware required.

• Direct mounting to a weak ceiling panel 

Use the optional HY-RR1 Reinforcement Ring. 

Use the cut-out section to insert the HY-RR1 into the ceiling as shown below.

Mounting hole

Cut-out section

HY-RR1 (optional) 

HY-RR1 placed on 
ceiling panel

To the next 
speaker

From 
Amplifier

[If not bridging]

[If bridging]

Summary of Contents for F-1522SC









Reviews: