Toa DX-0808 Operating Instructions Manual Download Page 1

CAUTION

TO REDUCE THE RISK OF ELECTRICAL
SHOCK, DO NOT REMOVE  COVER.

NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL

THE LIGHTNING FLASH WITH
ARROWHEAD WITHIN A TRIANGLE IS

INTENDED TO TELL THE USER THAT
PARTS  INSIDE THE PRODUCT ARE A
RISK OF ELECTRIC SHOCK TO
PERSONS.

THE EXCLAMATION POINT WITHIN A
TRIANGLE IS INTENDED TO TELL THE
USER THAT IMPORTANT OPERATING
AND SERVICING INSTRUCTIONS ARE

IN THE PAPERS WITH THE

APPLIANCE.

CONTENTS

Please follow the instructions in this manual to obtain the optimum results from this unit.

We also recommend that you keep this manual handy for future reference.

TOA Corporation

OPERATING INSTRUCTIONS

MATRIX UNIT

DX-0808

1 . GENERAL DESCRIPTION

2. FEATURES

3. HANDLING PRECAUTIONS

4. SIGNAL PROCESSING FUNCTION

5. NOMENCLATURE AND FUNCTIONS

[FRONT PANEL]

[FRONT POCKET]

[REAR  PANEL]

6. PERSONAL COMPUTER CONNECTIONS

2

2

2

2

3

3

4

5

6

7. UNIT ID NUMBER SETTING

8. USING THE MEMORY I/O CONNECTOR

9. EXPANSION  AND  INTERNAL  SWITCH 

SETTING

1 0 . RECALLING THE PATTERN MEMORIES

1 1 . SPECIFICATIONS

12. APPEARANCE

8

9

10

11

11

12

Summary of Contents for DX-0808













Reviews: