manualshive.com logo in svg

Toa C-CV44-3 NTSC, Instruction Manual, Page: 2 / 16

Share
Download
Toa C-CV44-3 NTSC Instruction Manual Download Page 2

2

TABLE OF CONTENTS

1. SAFETY PRECAUTIONS

................................................................................ 3

2. GENERAL DESCRIPTION 

............................................................................. 4

3. HANDLING PRECAUTIONS 

.......................................................................... 4

4. NOMENCLATURE 

............................................................................................. 5

5. INSTALLATION AND CONNECTIONS 

...................................................... 6

6. ADJUSTMENT

................................................................................................... 10

7. ABOUT THE MODE SETTING SWITCH

7.1. Adjustment Switch ........................................................................................... 13
7.2. Backlight Compensation Switch ...................................................................... 13
7.3. Shutter Speed Switch ...................................................................................... 13

8. IF YOU THINK THERE IS A FAILURE: (TROUBLESHOOTING) 

..... 14

9. SPECIFICATIONS 

............................................................................................ 15

Accessories ............................................................................................................. 15

Summary of Contents for C-CV44-3 NTSC

















Reviews:

No comments